Having problems with your M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum ?

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot


Answers :

It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two small (18-22 gauge) wires from the unit and short across the terminals where the wires connect. If the unit comes on, the vacuum is fine, and it is most likely the low voltage control wires that have been damaged. It should be a pretty easy fix, if you can get to where the wires are located. They are probably just pulled apart at a joint. Good Luck!!
Repair Help & Product Troubleshooting for M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot


It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the


Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

Dust....dust....dust Hello, I recently bought a house with an older Electrolux Central Vac system. I'm unfamiliar with them, so I'm not sure how to deal with this: I cleaned up some mortar dust with it, and noticed not too long after that when I went into the garage, there was a fog of dust. The hose from the unit is venting into the garage. Is this normal? I have since used it for everyday household cleaning and each time I go back to the garage to a cloud of dust. Is there anything I can


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=113662&thid=662824\015\012Dust....dust....dust\015\012Posted by Kitkatman on Jun 11, 2008\015\012Hello,I re ... Electrolux Central Vacuum

My electrolux central vac outlets work on the main


Here's a great article about locating a clog in your vacuum: http://voices.yahoo.com/troubleshooting-electrolux-central-va ... Electrolux Central Vacuum

Vax powa 4000 wet and dry - no suction Both power and pump switches light up. Pump makes clicking noise. Vac motor only powers up briefley when in switched on cindition and mains plug is being inserted into socket.


... Vacuums

I have a 3 year old NuTone CV 353W central vac system and recently the switch on the hose handle does not turn the system on from any outlet in the house. I have to plug the hose into the outlet and then turn the unit on from the switch on the cannister. Any help would be greatly appreciated. Thanks


A great way to check if your switch in the hose is bad would be to turn the hose sideways in the inlet. If the unit turns on you most likely need a new switch. ... Broan-NuTone CV450 Central Bagged Central System Vacuum

On my Air Vac model AV425A Central Vacuum System, I discovered the circuit breaker opened. When I close it, the vacuum motor goes on. It doesn't matter which position the on/off switch is on, it runs until I open the circuit breaker again.


... M&S Systems ZX7000 Bagged Central System Vacuum

Sears vac mod 11627514700 main mot. will not start replaced board fuse and switch


... Kenmore Vacuums

When trying to use my Hayden Model 3600 central vac when trying to turn on the unit runs for 1 or 2 seconds and shuts off and continues to do so while switched on. I have thoroughly cleaned the filter and dirk canister but the intermittent running still occurs. Any suggestions?


... Hayden Industries SuperVac 3600 Central System Vacuum

My central vac unit does not turn off even when hose is disconnected. I have to unplug the motor unit in the garage to shut it off. What do you think the problem is? It is a 7 year old Electrolux


Possibly the power module. Or a short in the wiring. Take it to the local Aerus Electrolux store and have it checked by a service tech to be sure. The pm is a lot less expensive to replace than a whole cv. ... Electrolux Central Vacuum

I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?


... Easy Flo EF2300 Central System Vacuum

Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.


It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

Doesn't work Our home was built and finished in August 07.  The central vac doesn't work.  There is supposed to be a slot that opens in the kitchen where you sweep the dust and it sucks it up.  Also, the mounted unit on the garage wall has a hose that goes up into the house but there is a hole open at the bottom of the unit.  Where can I get someone to help us?  Or, is there an installation manual I can download to see if the builder did it properly.  He stole our solar heater for our pool and s


Has the slot in the kitchen (VacPan) been installed? Or is it just not working? There should be tubing coming into the unit in the garage, and possibly another piece to exhaust the unit to the outdoors, although this isn't always necessary. The intak ... Electrolux Centralux Vacuum

Nutone cv 353 central vac no power on main unit or when hose is installled in wall?


... Broan-NuTone CV353 Central Vacuum

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

I have a hayden premier supervac central vac system, while working on the switch in for the beater bar, the actual unit has turned off, the green light is no longer lit, is there a fuse on it somewhere or a reset button, i have tried unplugging it and replugging it in, but can not seem to get it to power up now?


Should be a reset on the main unit near the top ... Vacuums

My central vac is in the basement, I am getting suction in the basement, but no suction on the main floor and the second floor. How do I know if somehting is blocking it or if there is a hole?


That means that you have a clog in the lines where the basement inlets are connected to. They can be tough to get out, you might need to call a professional. ... Electrolux Central Vacuum

My Electrolux central vac wont cut off when you turn the switch off or unplug the hose from the wall. Any suggestions? Sheldon


Hi,\012The realy that turns it on is stuck... the relay will need to be replaced...\012\012heatman101 ... Electrolux Central Vacuum

Proline central vac is not suctioning, unless you are using the garage attachment


... Vacuums

Central Vac will not turn on.


These problems are nearly exclusively caused by a bad circut board and replacing it is the fix. Bad boards can cause many different effects so its nearly impossible to be sure. The 9v signal wire is not enough to short out an entire unit so it is ... Easy Flo EF1400 Central System Vacuum

Problems with Beam central vac


My Beam central vac has started turning off after about 10 minutes of use. I thought it was the hose, but the hose in the garage does the same thing, and I've also tried the other outlets, and the same. The canister was just emptied about two weeks a ... Beam Industries 2775 Serenity Plus Central System Vacuum

I have a model 1561 electrolux central vac..can i use a hose and accessories from a model 15448 model electrolux central vac to compliment my central vac unit


If the hose fits into the inlets, then there should be no problem. ... Electrolux Centralux Vacuum

Central Vac does not shut off


I would almost guarantee the relay inside went bad. its an inepensive part that any good vacuum tech or electrician could install. ... Vacuums

Hello, i have a Astec 110s central vac that shut down today.


That means that either the motor or the relay is bad. ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0385 seconds