Having problems with your M&S Systems Vacuums ?

My Air Vac is 20-21 years old. Recently it stopped running. I found the fuse by the motor was blown and replaced it. It blew immedicately when I turned it on. I think I need to repace the motor. Do you agree and can I buy a motor from you.?


Answers :

If the fuse does keep blowing yes you do need to replace the motor. I am sorry we do not sell parts though. Try the link below to get the motor.
\015\012
\015\012http://builtinvacuum.com/help/airvac.html
\015\012
\015\012Good Luck
If the fuse blew up right the way it means that the short that caused the first fuse to fry is still there ..
Check the wires that supply the power and look for contacts or not coated wires in touch with the motor's case ..or such ...If all seam to be ok ..it means that the short is inside and you need a replacement for your motor..
Unfortunately we do not sell parts on this site ..and you should look for a replacement on the support site of the manufacturer..(keep in mind that sometimes the part and the handwork will not worth and will be in advantage a new one ..Just do the math first before getting one ..
Repair Help & Product Troubleshooting for M&S Systems Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Air Vac is 20-21 years old. Recently it stopped running. I found the fuse by the motor was blown and replaced it. It blew immedicately when I turned it on. I think I need to repace the motor. Do you agree and can I buy a motor from you.?


If the fuse does keep blowing yes you do need to replace the motor. I am sorry we do not sell parts though. Try the link below to get the motor.\015\012\015\012 ... M&S Systems Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

It sucks but the roller doesnt turn...I think my motor has burned out?are these vacuums made anymore? I also need the manual for the model 116 35913401 thanks


This is not a motor problem this sounds like a broken belt. Take the model and make # to your local used vac store and they can help you with the belt. If you dont or cant install it yourself bring the whole maching to them and they will do it for ne ... Kenmore 35912 / 35913 Progressive Upright Vacuum

Bissell 8910e Aromapro. Jams when being pushed along floor. I think brushes drop down and cause problem. However brushes turn when machine is laid flat. Motor works. Doe it need new belt ?


Check your depth adjustment on your brushes ... Bissell Vacuums

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ


I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??


... Eureka Capture Upright Vacuum Vacuum

My model 4870 Eureka type K Vacuum Cleaner won't turn back on after it started smoking. I turned it off, checked the belt and filters, and they seemed to be fine. The brush will turn so I don't think the motor is seized up. where do I go from here? Thanks for you help, David Andrews


... Eureka Smartvac 4870 Bagged Upright Vacuum

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like


I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.


There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

Stuck Roller Same problem here. I think in our case, the accumulation of hair and the increasing resistance the hair created over time caused the hair to start melting, and eventually the end cap was stuck to the roller, which prevented the roller from turning. I cleaned out the melted hair(?) as best I could, but I think I need to order a new roller and end caps.


Befrore you plunk your $ down ...\015\012\015\012I dont now that you melted the hair so much as you may have an accululation of gunk and hair. If there is a good (not 'fast food' type) auto parts store near you, go there and ask the cou ... Electrolux 1910 Bagless Upright Vacuum

Hi. think I need the manual. i added the water, turned on the power button, then turned on the rocker switch on the handle/wand and it seems to run and heat up but no steam


Put salt in the water.....sounds wierd but try it ... Tristar SB Steam Buggy Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My beater bar makes a noise and has a crack in the motor on the beater bar and is discolored--me thinks I need a new motor for the beater bar


Sounds like you're right. New motors are available at your nearest Aerus Electrolux store. They used to charge the same amount for selling the motor and letting the buyer install it, or for installing it in the shop. Worth checking in to.\01 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Motor wont turn on.I checked the switch and I think it is working.motor turns on if a put direct power to it.'but it smokes at the brushes. can you help?


This sounds like either the belt isn`t on right or the brush is not slotted in the vacuum right remove the plastic or metal cover from the bottom and check by inspecting the belts ability to easly turn the brush rod check with your hands DO NOT turn ... Kirby G4 Bagged Upright Vacuum

I have a NUTONE central vac, when I turn on the power, It sounds like its grinding glass and doesnt suction. Could it be that broken glass got caught in the motor and all I need to do is clean it, or is this the sound of a failed motor?


More likely it's something in the fan. However, I suggest taking it to a vacuum repair shop to make sure. Something could have got into the fan system and is making a racket, but the motor itself won't crunch up glass. ... Electrolux Central Vacuum

When I turn on my Eureka Smartvac 4870 is the light blinks sporadically and smells like the motor is burning. How can I tell if the motor needs to be replaced?


Hello. If the motor is running smoothly and the only symptom of a problem is that the light blinks sporadically I would inspect the wiring to the light. It may have a loose connection, or a burned insulation which is causing the burning smell. Onc ... Eureka Smartvac 4870 Bagged Upright Vacuum

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah


... Sebo X4 Bagged Upright Vacuum

The Dyson motor turns on, but the brush is not turning. What do I do? If it is a belt, we need to know where it is located and how to get into it.


Go http://www.youtube.com/watch?v=7_CtaFcc5HU ... Vacuums

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

Motor burned out need a replacement motor. Where can I buy one?


Are you sure it's the motor? I thought that was the prob w/mine when the brushes quit spinning, but it was a little clear piece of plastic\015\012 inside the middle of the handle had cracked. This piece holds the \015\012switch in place and is prob ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1081 seconds