Having problems with your M&S Systems ZX7000 Bagged Central System Vacuum ?

On my Air Vac model AV425A Central Vacuum System, I discovered the circuit breaker opened. When I close it, the vacuum motor goes on. It doesn't matter which position the on/off switch is on, it runs until I open the circuit breaker again.

Answers :

Repair Help & Product Troubleshooting for M&S Systems ZX7000 Bagged Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On my Air Vac model AV425A Central Vacuum System, I discovered the circuit breaker opened. When I close it, the vacuum motor goes on. It doesn't matter which position the on/off switch is on, it runs until I open the circuit breaker again.

... M&S Systems ZX7000 Bagged Central System Vacuum

My Sanitaire Commercial vacuum SC5815 A-2 does not turn on. It is quite new and seems to be "totally dead." Serial number: 0632005978 It is firmly plugged in, I have tried numerous electrical outlets, and I have tried the on-off switch numerous times. I wonder if there is a simple circuit breaker switch somewhere on the vacuum that I could switch without going to a repair shop? Or, I wonder if some latch is loose that shuts off the current, but I have checked the latches and they are clo

... Electrolux Sanitaire True HEPA Upright Commercial Vacuum Red EUKSC5713A

Handle got hot, circuit breaker was activated, now switch does not start vacuum

Hello. The cause of your hot handle must be investigated as you have a bare wire or connector which is shorting out. If you are handy, disassemble the handle assembly and look for melted rubber, a bare wire touching metal, etc. The fix is to repla ... Vacuums

Vacuum cleaner We have a panasonic MC-E47electronic which seems dead. It has a speed control which we nearly always had on full anyway. Have tested continuity through plug, flex and on/off switch and all OK. from then is open circuit through speed control which consist of slide rheostat and mystery small green box (2cm x 2cm x 1cm approx). Across motor there is negligable resistance. Machine is quite old and not worth paying out loads on poarts if it is safe to bypass speed control and connect

Yes it is safe, but i would make a switch? ... Vacuums

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Hoover EmPower 4600 keeps blowing circuit breaker. The number of outlets in the house that will allow me to run the vacuum is dropping quickly. It is a 4 year old house and all the circuit breakers are 20 amps. The vacuum only has a 12 amp motor. I am at a loss to solve this problem.

Take it to a friends house and plug it in if it does the same thing then the problem is in the vacuum cleaner.check your cord and see if there are anny cuts in it.you can open the breaker box then plug in the vacuum and watch the breaker box.you migh ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.

This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

My vacuum stopped working and tripped a circuit breaker in my apartment. I plugged it into a circuit with higher amperage, and the circuit tripped after the vacuum ran for a few seconds then a bit of smoke puffed out of it. I assume the motor is burned out. Can I repair this? Considering buying a refurbished one for around $70 - which is probably less than round trip shipping back to the manufacturer (this is way out of warranty).

... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

I have a 41a5021-18 chamberlain security+ 1/2 hp garage opener that requires constant pressure on the down position of the wall switch in order to close. If I release the switch the door reverses direction and completely opens.

... Vacuums

Kenmore Vacuum Model 116.35922500 Agitator starts/stops as you change handle position and/or move the vacuum. Seems like a switch, but the diagram shown in another solution doesn't seem to show a switch.

... Vacuums

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

My Kenmore canaster vacuum Mod# 116.25513506 runs continously when plugged in regardless of the on/off hand controlled switch.. Disconnecting the switch located on the hose assembly has no affect of the continous vacuum operation. What component in the electric motor circuit is at fault and what would be the cost of repair?

... Kenmore Vacuums

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.

I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The ON/OFF switch does not work. Unable to turn off vacuum without unplugging from wall. After removing handle, the ON/OFF switch is in ON position, but cannot be toggled to OFF position. Please assist. Thank you.

Replace the switch. Part number 28161067 ... Vacuums


I am not certain about this specific battery, however, if many batteries are unused for a long period of time, they can not be rejuvenated. \012Try the switch in each position for 24 hours and if there is no action, it is probably not worth re ... Black & Decker AV1200 DustBuster Handheld Vacuum

On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.

... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

On-off switch My problem is finding a source for an on-off switch for an electrolux vacuum sweeper model 2100. I have replaced the broken toggle and now the sweeper turns on but only as long as the outside button is depressed. It appears that the on-off switch itself is broken as the switch does not ''hold'' when the toggle is activated. It seems to return to it's ''off'' setting as soon as the toggle is released. What ''holds'' the switch in its ''on'' position? Does it depend only on the on-

Hi Hugh. The 2100 has a rocker switch under neath the button. it is probably broken, or the button has a worn detent spring. If you would like, I could send you a switch kit with the rocker, button, and detent spring enclosed for around 20 dollars ... Vacuums

I have the top of the line kenmore canister vacuum. According to the bottom plate the model nimbler is 116.28015700 I was doing the normal vacuuming and the bag full light came on and the vacuum action stropped. There is still power to the mortorized handle and agitator attachment. Is there some type of circuit breaker reset button for the vacuum function? This unit is probably less that two years old and has had very little use

... Kenmore Vacuums

Switch I have a kenmore 31913 vacuum and the on/off switch appears to be bad. My problem is getting into the switch. How do I open up the handle to get to the switch?

Go to this website\015\012and enter your complete model number in the search field in the upper\015\012right corner of the page. You should be able ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Lid to kenmore canister 360 hepa vacuum cleaner, lid to change vacuum bag stuck in open position

GoVaacuum2,\012\012I have the same problem and that didn't work.. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Vacuum stopped in middle of vacuuming our carpet. Would not startup at switch. Tried other electrical outlets wondering if this was the problem and checked breakers, but it still did not go back on.

2 guesses.... One is that you vacuumed up a pice of cord or sting that got wound up on the roller (if it's that tyme of machine, and NOW everything's completelt "loced." Cure: look at the brush roller and "unwind" the cord or string.\015\012 ... Vacuums

We recently bought a home with a 52" Hampton Bay Berlini Model 729 395 ceiling fan with a light that operates on a remote control. There is also a wall switch plate with two circular controls - one pushes and spins, the other turns with 4 clicks. We can not get the light or the fan to operate using either the switches or the remote. We have checked the circuit breaker. The manual that came with the unit - provided to us from the previous homeowner - really only describes how to install the uni

Nancy do you want to sell the Berlini fan if youstillo have it? ... Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3580 seconds