Having problems with your Miele S184 Powerhouse Bagged Upright Vacuum ?

I have a miele s184 and on the same side where the hose connects to the bottom of the vacuum, the housing is very loose. It does not come apart , but it looks like it could. I cannot locate a screw or anything to tighten. Can you help.

Answers :

Repair Help & Product Troubleshooting for Miele S184 Powerhouse Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a miele s184 and on the same side where the hose connects to the bottom of the vacuum, the housing is very loose. It does not come apart , but it looks like it could. I cannot locate a screw or anything to tighten. Can you help.

... Miele S184 Powerhouse Bagged Upright Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?

... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara

... Vacuums

I can see the height adjuster under my Bissell pet hair eraser vacuum, but it doesn't adjust. The parts don't look like they're touching. It's been iffy since I took it out of the box. Now it doesn't adjust at all. Used only five times. Looks like I should be able to fix it myself. No local repair available. Could you help please?

Http://uk.bissell.com/images/UserGuides/3920E_508.pdf\015\012\015\012This is the pdf manual. If you look at page 12 you'll see that the bo ... Bissell Vacuums

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti

You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo

The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!

... Hoover Steamvac F5860-900 Vacuum

I've never had to change a CFL bulb like the GE 35972 in my kitchen ceiling fixture. It looks like a squared off pretzel with the socket in the middle and facing up to the ceiling. It's been in there for years -- this is a rental -- and because it's so close to the ceiling, I can't tell where to pull the pins from the socket apart without breaking it. Any instructions or suggestions? Also, my Home Depot doesn't sell it; will the pins match a different CFL, like maybe a circular one?

CFL bulbs are held in place by a friction fit, but it is a very tight fit. Grasp the CFL by the sqaure plastic base and pull firmly away from the socket. You may have to wiggle it a little, but don't try to pull it out by the globe because they are ... GE Vacuums

GM 150 freestyle - need to separate 2 red halves to locate a problem. I am a retired electrician but cannot locate the means of opening the speed control end so that the whole top section may be removed. I would appreciate your help. Thank you. Ken.

... Nilfisk Vacuums

I have the scunci 1000 steamer- it was sitting for a while and the cap on the top looks like its corroded and i cannot remove it from the steamer - i just bought it a year ago, but i think the salt or vinegar from cleaning it got trapped in the top and i tried everything i could think of to loosen the top so i could pour water into the unit and use it again; otherwise it is in perfect condition, but i tried even pliers and i cannot loosen it and i dont want to break it, but am so frustrated - wh

Hi, Elaine, W/D here.Corroded items are difficult to break loose as the corrosion builds up a layer that binds the parts together. Try this, as I usually have good luck with this method:Tap around the perimeter of the cap with a wooden h ... Scunci SS1000 Handheld Steam Cleaner

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I purchased a used Minuteman 2400 series buffer/burnisher over the weekend from a store that is closing. The unit is about 7-8 years old. I did not get a manual with this item, can you help me out with this. I would like to read up on it so if I have problems I can look back on it. Even as far as the operation of it would help to have a book for it. Linda

I have this manual available via email. chris321 at gmail. ... Vacuums

S catch i have taken the top part of handle off, removed the screws under hose wrap, and layed the bottom part of handle down, i cannot find the s catch, can you tell me exactly where it is and what it looks like. i have looked all over this thing. thanks randy the model # is 8905

\015\012\015\012Just pull where I marked, it should come loose. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.

\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

Our housekeeper has twice pulled the cord out past the yellow marker and we've had it repaired both times at a cost of $75 ea. The housekeeper is now gone but I would like to try and fix the problem myself but cannot find disasembly instructions. Looking for some assistance as I really don't feel like spending another $75 if I can take care of it. Thoughts ?

Try this. Set vacuum on it's back end. Gently pull out cord and release. It may take a few tries, but should work\015\012Repair/service manuals are only available to authorized service tech at authorized Aerus Electrolux stores. These are i ... Electrolux Lux 5500 Canister Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.

May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still

This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum

Can you take the Swivel Sweeper battery pack apart to replace the batteries with new rechargeable batteries? Batteries look like AA or AAA, but it appears that the battery pack is sealed. Is there any way to get it apart:?

Yes you can if you have a way to cut through the plastic outer case,(I used a Dremel rotary tool). Inside you will find six double A Ni-mh batteries. I found eight of these for sale on ebay for around ten bucks,then all you do is solder some wire to ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

I took everything apart that I could but it doesn't look like tha vacuum comes apart in that area. The model number of my vacuum is 6596.

If you are trying to replace a belt, turn the vac. over and look for screws in the bottom under some small covers. If you can't get the covers off to access the screws try a small screw driver to carefully pry them out. ... Vacuums

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.

That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)

Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Telios TC3202 200W Cord Rewind is jammed - cannot see how to open body of vacuum to look at the source of the problem. Found 4 screws but that did not help - guess you have to prise something open but cannot see where or how.

There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about the others. \015\012Anyway, this is it. The cover is held to the b ... Vacuums

I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!


Dyson DC17 Animal User's Guide says put plunger in out position. I cannot get the plunger to move and I'm not really sure if I'm trying to move the correct part. Cannot locate my user's manual for help.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.5933 seconds