Having problems with your Miele S251i Plus Bagged Canister Vacuum ?

My circuit board has a short on the soldering for the DC rectifier that supplies the carpet cleaning motor. Where can I order a new circuit board. Miele S251i

Answers :

Just a suggestion, but you could try to re-solder the connection on the board. some of the circuit boards did not have enough solder on the board coming from the factory.

That being said, if the component is damaged due to the burning, I suggest you contact your local Miele dealer and have them order you a circuit board for the unit.

IF the unit is less than 5 years old as well, that part should be covered under warranty. Do NOT solder it, just have them replace the part.

Good luck
Repair Help & Product Troubleshooting for Miele S251i Plus Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My circuit board has a short on the soldering for the DC rectifier that supplies the carpet cleaning motor. Where can I order a new circuit board. Miele S251i

Just a suggestion, but you could try to re-solder the connection on the board. some of the circuit boards did not have enough solder on the board coming from the factory. That being said, if the component is damaged due to the burning, I ... Miele S251i Plus Bagged Canister Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?

... Miele SEB 213-2 Vacuum

Miele S318i worked ok till I took it apart to blow really fine ceiling "popcorn" dust that got sucked by the filters. When I plugged back in started for a milli second and quit. At this point I believe the circuit board might be the fault, but I want to test motor before I go and buy the part. Can I simply run 110 to the two moter contacts to bench test? Steve

Yes, you can. ... Miele S318 Bagged Canister Vacuum

Took my miele canister vacuum cleaner in for repair because the cord had a break in it creating a short. He said it also needed an inter filter ($12.29) and the carbon brushes were worn out ($21.95). Is that possible? Also wanted to service the motor and put in a new seal ($49.95) Shouldn't that include the inter filter and carbon brushes?

Depending on the age of the vacuum and how much use it gets, the first two are possible. I would question the brushes as they should last for several years.\015\012The servicing is generally for labor only and doesn't include parts. I do reco ... Miele Vacuums

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?

Probably needs a new hose. ... Vacuums

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.

... Miele S251 Flamenco II Bagged Canister Vacuum

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah

... Sebo X4 Bagged Upright Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a

... Electrolux Vacuums

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

Our Hoover U8172-900 brush motor is not working. Do you have a wiring diagram so I can determine if the motor circuit board is the problem or the motor?

No diagrram is necessary unless you have dismandled.\012Check if the brushes are touching the mtor commutator. If not you can easily remove both the brushes and polish the surface evenly .Insert only after cleaning the motor commutator till the ... Hoover Vacuums

Hoover Savvy U8174-900, replacement circuit board LED/Brush Motor

\015\012 \015\012 \015\012 \015\012 \015\012 ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I am looking for a contol board for a miele s143 stick vacuum. The vacuum wont start but when I supply power directly to the motor it spins. I think the switches are OK so I have concluded it is the control board Thanks Don Kenney

You should check the cord and switch's for continuity, the boards are usually pretty reliable, you could check the board for any bad solder joints, at least that would be obvious. ... Vacuums

My robot will not charge. Tried multiple resets and new battery from irobot.com (both suggested by Irobot customer service) but got nowhere. The vacuum did work for a short time (until the new partially charged battery ran out). If I bypass the internal charging circuits and charge directly from the charger (with jumpers) the robot seems to work fine. Unfortunatey, there is no mechanism to turn off the charge cycle, so this is not practical.

Replace the battery charger ... iRobot Roomba 4210 Bagless Robotic Vacuum

Singer Commercial 16-188 S/N G 9466420. Just got new Table, Stand & Motor. The pulley on the Singer does not line up with the belt slot in the table top. Can the pulley on the machine be moved out or is this the wrong table? Table, Stand & Motor was ordered for the 16-188.

... Singer Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work

It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo

It sounds as if you have a clog inside the "Power Nozzel". They mention that there are "no user serviceable parts within the Majestic® Power Nozzle" My advice would be to see if you can see a clog with in reachable distance and try to remove the ... Filter Queen Vacuums

Hi, my circuit board resistors are burnt due to my re-wiring the resistor switch. How do I fix this - S3755 wiring diagram?? need to know the correct resistors or get a new board

The only way is to get a replacement board. even the dealers are not provided with that level of wiring diagrams. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

I have a Simplicity (Danby) SDR458H Dehumidifier. The bearings in the fan motor have become loud and scratchy sounding (due to a plugged-up filter in the past). I would like to get a repair manual for it with part numbers so I can order a new fan motor.

... Simplicity Vacuums

Eurika Whirlwind vacuum cleaner. Nearly new. Suddenly lost succion.l I cleaned and dried the filter. It developed an odor, then stopped short. I believe the motor may be burned out. Motor is cool, but it won't start. Is there a fuse??t

Look around the nozzle it might have a reset switch ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

MRG 720-42/2 Hi, I have a vacuum Miele and the motor failed....and now I would like to buy a new one. The motor type is MRG 720-42/2 If you know where could I buy it, please let me know...... Many thanks is advance. Carlos Suarez [email protected]

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1718 seconds