Having problems with your Miele S251i Plus Bagged Canister Vacuum ?

Miele S251i power brush replace belt

\015 Belt\015

Answers :

Repair Help & Product Troubleshooting for Miele S251i Plus Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Miele S251i power brush replace belt


... Miele S251i Plus Bagged Canister Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

How to install drive belt on SEB 204 power brush for miele s324i


... Vacuums

If the power brush does not roll, I presume it would be a belt. Where can I get a replacement for this model? Do you know of any diagram for the unit or how to remove the belt? Many thanks,


... Easy Flo SQ9020 Bagless Central System Cyclonic Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?


Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

The power nozzle works but only on tile. the brush does not turn. the belt is intact. could the motor that turns the belt be broke? is this something i can replace myself or is it better to bring it to be serviced


Depends on you if you feel you could possibly repair it by replacing the electrical motor or you may just have a wire thats nolonger getting continity. enevitably it's your decision if you can repair it you will come off cheaper :) ... Electrolux Guardian Bagged Canister Vacuum

Have an e-series rainbow. Belt and brush bar have been replaced in power head. But the red reset button can still be pushed and it is not staying going like it should. May it be the motor?


... Rainbow E series Canister Wet/Dry Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

How do I replace the power brush belt? - Bissell 8910 ProHeat Clear View Upright Vacuum


This machine needs to be taken to a dealer to replace the belt. It is hooked into the pulley and pump assembly and is a nightmare to fix. ... Bissell 8910 ProHeat Clear View Upright Vacuum

Power-mate jr belt appears to be loose, as will not turn brush. Can it be replaced? Looked online and could not find one.


Greetings,\015\012\015\012You're in luck! I found the belt for you Powermate Jr. below; If you need help installing this belt, please start a new repair here on Fixya, and I'll be more then happy to walk you through the repair of this. ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Can't find replacement drive belt for bissell easy vac power brush model 3108


Go to bissell.com and look it up there.or call all-type vacuum and janitorial supply and ask for lisa or bonnie.tell them pete reccomended them.314-275-8006 ... Vacuums

Shark vacuum nh15 replacement pet hair power brush replacement


... Euro-Pro Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.


First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

Miele S514 Solaris Electro Plus with Power Brush. Bought it in 2003. I love it, except the Power Brush just lost power so now I can't vacuum the carpets. I believe it is a SEB 212-2 Power Brush. The vacuum (canister) is Black. Any help is appreciated. There is no power to it at all. I've unplugged it, smacked it around a little too (mostly kidding) but still nothing.


... Miele S514 Solaris Electro Plus Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

How do you replace the belt for the Miele SEB236 Powerbrush?


If you take the sole plate off you will see the belt on the brushbar ... Miele S5980 Capricorn Canister Vacuum Cleaner with SEB236 Powerbrush

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1057 seconds