Having problems with your Miele S318 Bagged Canister Vacuum ?

How does the Miele Vacuum Power Nozzle Pinion Gear get taken off and a new one put on? Is it pressed on and just need to pull off or is it screwed off. It is for the SEB217 power head

Answers :

\015\012What you need to do is screw the Pinion Gear off of the power brush. This can sometimes be tricking, because as I'm sure you're aware, when you twist the pinion gear to try and release it, it also spins the motor as well. What I've found to be the easiest way to replace the pinion gear on these models is by putting a very small flat head screw driver into the vent on the motor. Be very careful when doing this because there is a fan inside here. I've circled the area that you should put the flat head screwdriver into below;
\015\012Once you have the flat head inside, pull the screwdriver towards you while you turn the pinion gear away from you. It will come off with just a little bit of elbow grease.
\015\012When you install the new pinion gear, just use the screw driver the same to tighten the pinion gear onto the motor shaft.
\015\012Please feel free to request a clarification to this repair if you have any further questions or concerns that I can answer for you.
\015\012I hope this helpful to you in fixing your Miele. If it was, may you kindly rate my repair as helpful? I really would appreciate that, thank you so much.
\015\012Thanks again,
\015\012Chris J.
Repair Help & Product Troubleshooting for Miele S318 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How does the Miele Vacuum Power Nozzle Pinion Gear get taken off and a new one put on? Is it pressed on and just need to pull off or is it screwed off. It is for the SEB217 power head

Greetings,\015\012\015\012What you need to do is screw the Pinion Gear off of the power brush. This can sometimes be tricking, because as I'm sure you're aware, when you twist the pinion gear to try and release it, it also spins the mot ... Miele S318 Bagged Canister Vacuum

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?

Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum

Need to replace belt on Eureka Powerline 12.0 vac. Screws look like Torx head or something on bottom of vac. Are those the screws that need to come out for changing? If so, what size do I need?

No, do not remove the torx head screws for a belt change. If there are any screws that need to be removed for the belt change, they will be phillips head. What is model # of vac?? ... Eureka Vacuums

Need to replace power head for blue magic Need

... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Power head and wand connection is intermittent.

If there is a rubber bumper on your power head you must slip it off before the two halves will separate. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Honeywell HF810 fan. I am trying to clean it. I removed the phillips head screws, but their are two odd screws that require a special tool to remove them . I also have to go through the plastic shaft, so I need a special type of screwdriver and a special type of head. Thanks for the challenge!!

... Honeywell Vacuums

I have an S3630 Hoover Windtunnel with a Mach 6.1 power head. One of the wheels on the back of the power head broke off. I will need the back under pannel with the back wheels. Where can I get these parts?

... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

Power head for my central vacuum powers on and need to be pushed

What brand system is it? by not moves do you mean it doesn't pull itself forward? chances are its a cheap rubber belt that is stretched out and needs to be a replaced. ... Electrolux Central Vacuum

The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?

You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic

... Vacuums

Need drawing to reassemble power head

Hello,\015\012\015\012I have attached the parts drawing of the power nozzle that came with the Red Velvet model, or the SEB236. Unfortunately the way that it's posted online, it's done in a way that makes saving the picture and posting t ... Miele S558 Red Velvet Bagged Canister Vacuum

My samsung quiet storm modl 9068G needs a new brush in the power head. Where can I get one?

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.

Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey

... Vacuums

Need part for stand of Hamilton Beach Scovill Model 44 Mixer. Part is locking rocker tab that hold mixer in place on stand or press to remove mixer head from stand. Don't need spring or pivot pin, just rocker tab. Don't have part number.

... Vacuums

The power head of my 1165581590C Kenmore Power mate Whispertone 12 amp vacuum won't open. It is an older model and it desparately needs a clean!

I am not 100% sure of the model number but most of their powerheads come apart quite easily if you know how. There is a light lens cover on the top of your powerhead. On each side of this cover there is a little clip that holds it in place. You ca ... Vacuums

How to disassemble electrolux ZAM 6280?i had already removed screws and don't know to disassemble it. i need to check fuse or if it needs resetting.i'm using it and it suddenly stopped completely.no power at all.

Hi There.. I had the exact same problem with my ZAM6280 model. The PCB part (location C8) had blown. Do you know the details for that part, so I can replace it? Otherwise, you didn't happen to come across any schematics for the PCB Module?? ... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

Wispertone 116.29429990 I need help in getting the cover off. The foot retractor pedal for the power cord has screws under it and I am afraid of breaking the it. How do I access the screws under the pedal?

The pedal may be tough but the attached pushrod that disengages the power cord reel ratchet may not be, and is stressed by reddevil6's maneuver. I'd prefer to go after the tabs that retain the pedal's forward end. They are part of the rear cover and ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

I have a Dyson DC17 and I cannot get the detachable hose to pull up to use. I have tried pulling it up but it does not move and I can not use my detachable pieces. Is there a button I need to press - How do I fix?

Yes there is a button to release it near the handle i think , \015\012\015\012hope this helps ... Vacuums

The power head on my progressive vaccum doesn't seem to power on. Nothing appears to be stuck and not sure if I need to take it apart?? suggestions

... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

I have a shark infinity model no. NR90C and I need to purchase a new power head. I need to know where to buy and how much they are

... Infinity Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1058 seconds