Having problems with your Miele S514 Solaris Electro Plus Vacuum ?

Solaris electro plus need replacement roller brush for electric carpet cleaning head

\015 Bristles no long enough to pull lint up off carpet, suction is fine just can't dislodge fibers from carpet to allow suction to do its job\015

Answers :

The part number for the roller is 4929740 if you are in Australia or NZ we can get the part for you (VacuumSpot)
Repair Help & Product Troubleshooting for Miele S514 Solaris Electro Plus Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Solaris electro plus need replacement roller brush for electric carpet cleaning head

The part number for the roller is 4929740 if you are in Australia or NZ we can get the part for you (VacuumSpot) ... Miele S514 Solaris Electro Plus Vacuum

Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?

Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?

Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Need to replace the main belt on my Bissel 1698-P. Can't figure out how to get the belt around the brush roller. Have the top off. Cleaned the water tubes, didn't let the water come down.

Remove belt access door at left front of unit.\015\012\015\012Unplug the unit. Remove the two solution tanks.Remove spray tips from guides.Remove the brush and cog belt by removing the screw from the orange retaining collar.\015\012Remove belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?

The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey

... Vacuums

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?

... Dyson "Stowaway" Canister Vacuum Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr

Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee

Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?

Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Miele S514 Solaris Electro Plus with Power Brush. Bought it in 2003. I love it, except the Power Brush just lost power so now I can't vacuum the carpets. I believe it is a SEB 212-2 Power Brush. The vacuum (canister) is Black. Any help is appreciated. There is no power to it at all. I've unplugged it, smacked it around a little too (mostly kidding) but still nothing.

... Miele S514 Solaris Electro Plus Vacuum

Need belts I am in the middle of cleaning my carpet and need a power belt and roller belt. Who sells them locally. 30127 Powder Springs, Ga

If you local repair shops don't have them, I am sure they can order them for you. Just have to check you yellow pages, also under Sew and Vac stores, most offer service as well as sales. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?

If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

My brush roller stopped spinning so I had to take it off and clean out all the hair that had gotten wound around it. I replaces it and now it is make a lound noise, but only when the brush is on. Could it be the belt making such a loud sound? It wasn't making this noise before.

Could very well be the belt.\015\012When cleaning the brush it is a good idea to add some WD40 at the ends where the plastic pieces are that hold the brush in the vacuum. The brush needs to be able to move freely around the plastic pieces.\015\012Ad ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Brush roller spins until it touches the carpet, then stops. I have already replaced the belt and it continues to stop when it touches the carpet

Saw another answer saying to put electrical tape on the brush roller where the belt contacts it. I was thinking that the brush roller bearings have probably worn out, and the roller needs to be replaced. But electrical tape is a lot cheaper. ... Eureka Smartvac 4870 Bagged Upright Vacuum

How can determine when it's time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I'm cleaning? Thanks, Jim

Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck! ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1149 seconds