Having problems with your Miele S514 Solaris Turbo Plus Vacuum ?

Miele Solaris height adjuster arm won't snap back in

\015 Trying to figure out a problem with my Miele Solaris Turbo Plus 234/236 powerbrush, I started taking apart the powerbrush. I figured out the problem but now I can't get the height adjustment bar back in. I figure something inside must catch the metal part that dips into the bottom of the powerbrush, but I can't see any likely mechanisms when I open the powerbrush bottom up. And it doesn't seem to snap in. I don't remember how I took it out...seems it just snapped out. Am I missing a piece? Any help would be appreciated, as this isn't my vacuum!\015

Answers :

Maybe this picture will help, put the pieces together, then it sits directly under where #230 in the pic.
\015\012
\015\0122da4be9.gif
Repair Help & Product Troubleshooting for Miele S514 Solaris Turbo Plus Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Miele Solaris height adjuster arm won't snap back in


Maybe this picture will help, put the pieces together, then it sits directly under where #230 in the pic. \015\012\015\012 ... Miele S514 Solaris Turbo Plus Vacuum

Can't get my Miele Power Brush SEB 236 Back together. Height adjustment mainly. Not sure where 1 loose spring goes either and which screws go where. Got it back together and had 3 left, then a 4th fell out when I vacuumed.


... Kenmore Vacuums

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?


The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums

Height adjustment knob wont adjust anymore, its loose. was turned too hard.


Try this link http://www.vacsite.com/en/bissell-parts-1/bissell-parts/6594-powerforce-bagless.html ... Bissell 6594 PowerForce Bagless Upright Vacuum

How do I put the height adjustment knob back together on the bissell power force helix upright vacuum


... Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Eureka 3276AVZ Height adjustment knob wont turn


... Eureka 3276AVZ Bagless Upright Vacuum

Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to


When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums

Still dont know hot to get height adjuster knob to work. tried handle all the way back n lay on side solution that was offered. the plate has a permanent place to sit. hows it possible to bring knob


Hey, not having a working height adjustment can be a bear. Lock the vacuum in the upright position, change the knob to desired setting, and recline the handle for adjustment to occur. If you are still having difficulty, you may want to have y ... Bissell 6594 PowerForce Bagless Upright Vacuum

Dyson DC04 hello, my dyson seems to run ok in upright but when i tilt back the motor sounds like it is struggling, do you think it's down to the rollers being to low and can you adjust height of rollers to overcome said problem? yours chris


Hi.\015\012\015\012If the motor is struggling check to see how easy it is to rotate brush by hand it is stiff to rotate the bearings in the roller may be siezed or the roller could be clogged with hair etc check it & let me know what ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

Transmission adjustment I need to know how to put the arm back on and how to locate it


Http://www.greatvacs.com/Kirby%20Transmission%20Adj.shtml\015\012\015\012this is a link to a site with instructions for adjusting the ... Kirby G5 Bagged Upright Vacuum

Eureka Upright Vacuum 4230 Series. Spring popped off on height adjustment knob. Where does it go and how do I put it back on?


Sure would like to know that answer myself does anyone know how to put the spring back i am about to lose my ever loving mind ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I had to replace the idler arm assembly because it snapped. I then had to put the torsion spring in place and that is where I am having trouble. I cannot seem to find a diagram that shows how it goes back into place.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Height adjustment The height adjustment button on my upright is nonfunctional.  The Height is set closest to the floor and it makes it difficult to move on medium height carpet.


You'll have to turn the upright to its side to show the sole plate where the rolling brush is. Check where the front wheels are located and ensure there is no blockage obstructing the rotary dial. Sometimes the spring mechanisms can work themselves l ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

Kenmore Powermate foot pedal doesn't adjust the height anymore


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Getting the height adjustment to work


Is this a piece of **** dirt devil? if so, even when you get it back together the design is so flawed that it will keep breaking the belts, I've already gone through 3 in a week! see my other suggestions to remedy this. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works


... Hoover Vacuums

Hoover u6476 Windtunnel nozzle height adjustment cam repair


... Hoover Vacuums

Hoover u6476 Windtunnel nozzle height adjustment cam repair


... Vacuums

Eureka Boss Capture - bagless upright - height adjustment knob


... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Eureka Boss height adjustment not working so brush stops turning


... Eureka Boss? SmartVac 4870MZ Bagged Upright Vacuum

The hand-held wand wont slide back into the tube. It wont go down far enough to click in and become the handle again. It was working fine but all of the sudden won't fit back in.


Sounds like the tube has something inside of it that is obstructing the path. veriffy the the "female" end of the tube isnt obstructed, and also, make sure that nothing is bent ( which can happen easily). use a flashlight to shine down into the tubes ... Dyson Ball DC24 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0558 seconds