Having problems with your Miele S548 Bagged Canister Vacuum ?

Canister vacuum keeps turning off, can push buttons on wand handle to restart but shuts off again as soon as you start to move handle


Answers :

Its sounds like the problem is either the power head wire which when your using it and twisting it left and right, turns it off.. Or it could be in the hose where the connect meets with the unit.

Here's a number to call to further assist you. 1-800-322-2965
Repair Help & Product Troubleshooting for Miele S548 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Canister vacuum keeps turning off, can push buttons on wand handle to restart but shuts off again as soon as you start to move handle


Its sounds like the problem is either the power head wire which when your using it and twisting it left and right, turns it off.. Or it could be in the hose where the connect meets with the unit.Here's a number to call to further assist y ... Miele S548 Bagged Canister Vacuum

GE Spacemaker Microwave PVM1870 fan keeps running after door closed and won't shut off. Have to open door or unplug. As soon as door is closed and plug is back in, fan starts up. If door handle is pressed downward, microwave starts! If door handle is raised, fan shuts off but light stays on.


... Vacuums

Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.


Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?


... Miele s558 Silver Moon Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Elna 2007 does not Zig/Zag Adjusting stitch width does move the needle but it does not move back-and-forth while sewing. I am an engineer so I can handle any task; but, I didn't want to start dissasembling without some knowledge. Look before you leap.


... Vacuums

Roomba 4270 stops too soon. my roomba got weird all of a sudden. it started not moving all over as it should. so I tore it all down as I had done before and cleaned all the hair and dirt out of every thing I could without getting down to the basic shell. it does work now and does move all over but stops after about 10 minutes. brand new battery so not a battery issue. could I have plugged some of the sensors in the wrong 'plug'


... iRobot Roomba 560 Robotic Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

Less than 1 year old Bissell Healthy Home 15 in. 12 amp. Brush shuts off when it is not suppose to if you move handle up and down while in vacuuming mode it engages then disengages. Dosen't matter what height brush is set at.


That machine is made to do that, there is a safety switch in the base of the machine that shuts the brush off when the handle is in the upright position. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks


... Eureka Bravo II Bagged Upright Vacuum

When you start it, it will turn and go backwards but will not move forward, will do this for about 30 seconds then shuts down and gives one beep.


\015\012\015\012\015\012\015\012\015\012Your bump sensors are malfunctioning. I had the same problem. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend.... ... iRobot Roomba 530 Robotic Vacuum

Could I have a short in my cord? I can vacuum & then when I move the canister it shuts off, if I wiggle the cord it will turn back on. This last time, it just revs like a car trying to start & then does nothing. I live in a VERY remote area (80 miles from nearest Wal-Mart or McDonalds) so I know I will not be able to find someone to repair this for me. I have great doubt that I will be able to do it myself & my husband is an accountant so he is unavailable for another 6 weeks!!!!! Any suggestion


Whit the vacume plugged in and turned on start where the cord goes in to it and hold the cord whith each hand and bend it slightly. Move up the cord and do the same if there is a brake in the cord the machine will loose power until you bend the secti ... Miele Red Star Bagged Canister Vacuum

I got a mp3 player philips gogear 2 gb sa2825 it just get started when i put it in charging as soon as i remove .... it shuts down ...??? if i try to turn it on it dosen't can i know what is the problem


Hi, you have a fault with the battery it must have bad cells or faulty connection the only way your going to solve this problem is by getting the battery replaced ... Vacuums

My beam serenity plus power head shuts off as soon as it hits our carpet. It runs when held off the floor though. Do you know what could be causing this? The only thing that starts it up is the red reset button.


... Beam Industries 2900 Serenity Plus Central System Vacuum

Hoover Self Propelled Wind Tunnel. Keeps throwing off drive belt. New belt. Starts up fine, as soon as you release and lower handle, belt comes off spindle


Hi, it sounds as though that when you release the handle, I no this puts pressure on the brush or spindle, this is causing the belt to come off. You need to remove the roller brush and check it for any thing that may have rapped around it causing it ... Vacuums

When i move the switch up,the motor doesn't start. its a turbopower 52oo .is there a rod that activates the switch? for the last 2 uses it ran as soon as it was plugged in.


The rod on those are so flimsy when the switch gets old it gets stiffer to operate and the rod just bends away. replace the switch and it will fix the problem. ... Hoover U59 WindTunnel TurboPOWER Bagged Upright Vacuum

Epio 6500 canister electrolux won't stay running...says the bag is full even when it isn't. Will start but as soon a load is placed on the unit it shuts down. Any thoughts?


There might be something stuck ... Electrolux Epic 6500 Vacuum

Vacuum won't stay on. When I push the button to start it, the motor shuts off as soon as I let go of the button.


You have a broken switch (replace) or hopefully something caught under the switch. Regards Billy ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My vacuum won't stay on. Will start when I push on button but will shut off as soon as button is released.


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bissel home healthy vac. The brush only turns on for a split second and shuts off. Each time I put it in the upright position and start over, it does the same thing. I thought it may be the switch up on the handle. I replaced it, no luck.


Here is some information about a second Auto Cut-Off Switch near the power switch:\015\012About the only "gripe" I can come up with has to do with the automatic brush shut off mechanism that causes the brush to stop rotating when the unit is mo ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

The Roomba 535 runs but stays in 1 spot moves 2 inches turns and repeats the process about 10 times. then a red indicator light starts blinking and the unit shuts down


Any beeps? If so, how many?\015\012\015\012Is there a pattern to the light blinking?\015\012\015\012Not really enough info yet to be certain, but it sound like the cliff sensors may be dirty. \015\012\015\012Here ... iRobot 530 Roomba Vacuuming Robot, White Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.


The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0560 seconds