Having problems with your Miele S7210 Bagged Upright Vacuum ?

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


Answers :

There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear panel of the lower body. If it's in there and stuck, just realign it with the 2 grooves on each side or remove it completely; it is a dust shield after all. The best fix is to replace the rear panel and dust shield and they are ordered together and the cost is fairly low. Also check the alignment of the rear body panel at the bottom There are 2 tabs that protrude down about and inch on each side, the one closest to the handle release lever sometimes gets bent and causes the unit to jam. If this does not help there is one more solution involving the rear wheel assembly. check to see that the rear wheel axel is straight, meaning both wheels are parallel at all times while releasing the handle. If the axel is crooked, the wheel assembly must be replaced and you should have a Miele service center order the part and do it for you.
Repair Help & Product Troubleshooting for Miele S7210 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

Hi i have just been given a dysondc07 hepa could anyone tell me how to release the upright handle as to start hoovering it seems to be stuck upright thus unable to commence


Take off the power cord from its two hangers, depress the coloured clip above the power switch and the wand will lift out along with the back telescopic hose. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The kickstand seems to be jammed and the vacuum will not stand upright. I am not able to release it How can I fix it ?


Hi there,I'm sorry to hear you're having difficulties with your Dyson cleaner. From your description of the issue, it sound as though you may own a DC25, rather than a DC28. To realign the stabiliser pedal so the cleaner will stand upright, pleas ... Dyson DC28 Animal Bagless Upright Vacuum

Hoover windtunnel tilt mechanism won't remain locked in upright position or at any of the fixed angle positions - now any slight bump and the lock releases. Normally you must manually use the small foot pedal release on the left side as you face the vacuum from behind.


Hello, stanI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Our Samsonite Pixel Cube suitcase combination lock won't unlock! We are definitely putting the correct combination into it but the lock isn't moving and the suitcase is full of our belongings! We've used it on numerous occasions before and never had a problem with it so can't understand why it has suddenly jammed!


Try 001, then 002, then 003 and so on. It may take you half an hour but worth the try. Otherwise, if you don't want to break it open, you really have to call Samsonite Customer Service Center at 1-800-765-BAGS. ... Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Miele s7000 I clicked my upright into sitting position and accidently bumped the foot release knob. The body fell back and now I can not get it to click back into upright sitting position. Something is now in the way of it locking into place. This happened last year and it was under warranty. it no longer is and I would like to be able to fix it myself in the future. Can you help me? Thank you. Kacee in Oregon


... Vacuums

Fantom Thunder vac....beater bar quit rotating - can't even move it manually....seems to be locked up.


... Fantom Vacums XT450K Upright Vacuum

I have a Dyson Animal DC 28. It vacuums fine on floor mode, but, when locked in the upright position it releases pressure though the little valve behind filter a. I have only had it for 2 weeks so I'm hoping the filters don't need to be cleaned this often! I would like to finish vacuuming without waiting 24hrs for the filters to dry.


Unfortunately with any bagless vacuum the filters do need to be cleaned or replaced very frequently for the vacuum to perform. But the good news is it sounds like you have a clog in the hose. remove the attachment hose as you would be using it and un ... Vacuums

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

The upright part seems locked. I can't pull back to vacuum.


Hi there, so we can help you, please call us on 1866MYDYSON!Kind regardsDarranDyson Customer Service ... Dyson DC28 Animal Bagless Upright Vacuum

Sucked up a sock now the brush doesnt move - Dyson Ball DC24 Bagless Upright Vacuum


... Dyson Ball DC24 Bagless Upright Vacuum

Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.


... Vacuums

I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!


... Sharp Twin Energy EC-TU2607 Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Eureka the boss upright bagless vacuum. how do i open it to get to the belt area? the brush seems stuck. it wont move


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=801547\015\012Generic problem for all Vacuums\015\012Eureka the boss upright bagless\015\012 ... Vacuums

My Bissell spot bot stopped sucking the solution from the container. When we had the problem before we just reseated the container and it started releasing the water/solution. There is a funk little hole that takes water from the container and it seems to move around a bit. We own 3 spot bots, and have had trouble with all of them.


... Bissell 12005 Spot Bot Handheld Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I am having trouble with the nozzle control knob on my Hoover Elite Upright. I was cleaning out the bottom of the machine and the knob fell out and now I cant align it properly. It seems loose and not doing anything when I move it


Hello : My advice to take it to the service if you still have the guarantee . Or provide detailed information about your Hoover to get better help . good luck . ... Vacuums

My Dyson DC27 Animal is stuck (Locked) in the upright position. Everything seems to be ok with no apparent cracks or breakages. I don't want to force it in case something snaps.


Dysons are notorious for this problem. You will have to just force it and clean any obstructions. ... Vacuums

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean


... Panasonic Vacuums

Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?


After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums

We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!


These belts need to be changed every 6 months regardless of the way they look. ... Vacuums

We just moved and the movers didn't pack my Miele vacuum, they simply transported it as is. Now the piece that is supposed to interlock from the hose into the canister seems to be missing. Can you tell me how to get a replacement piece?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=730491\015\012Generic problem for all Vacuums\015\012We just moved and the\015\012Posted by trumbull on ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0651 seconds