Having problems with your Miele S7210 Bagged Upright Vacuum ?

Miele S7210 Has a blockage within motor area, rest of attachment clear

\015 I bought the S7210 2 yrs ago and no problems until now.. I just put in a new vacuum bag, and changed the other two filters. When attempting to vacuum carpet, after 2 minutes the normal sound shifts quickly to a louder, grating one. I checked the motor area by touch- defintely heating up. I examined the rest of the vacuum assembly, hose external and internal as the pathway travels up the cannister and into the collection bag. There was some blockage- hair and dust at the bottom- which I completely removed and checked with a stiff wire to make sure all was clear. If I disconnect the hand piece there is plenty of vacuum, but the motor still is labored when I try to vacuum carpet. I suspect I waited a bit too long to change the bag, and got junk into some grid protecting the motor, preventing air from flowing properly. I am pretty handy with tools, I live in the middle of nowhere (the local vacuum repairman said in response to my ? 'Are you an authorized Miele repairer?' with 'Miele? Is that a vacuum? Never heard of it!') Would anyone who knows the solution to my problem here please be willing to share with me their expertise?\015

Answers :

Repair Help & Product Troubleshooting for Miele S7210 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Miele S7210 Has a blockage within motor area, rest of attachment clear


... Miele S7210 Bagged Upright Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

Motor sounds loud and high pitched. Suction seem ok, can't find any blockages. Cleaned filter at top of removable canister. Exhaust seems hot and low. Can there be a blockage within the motor housing?


Most likely your bearings are shot. it will need a new motor ... Kenmore Vacuums

Motor just makes 4 or 5 small clicking noises when you pull the trigger, then stops. The little lights illumintae around the "max" button as well. However, the motor does not engage in the slightest. There is no blockage at all. I have owned the vac for 10 months and know the sounds of blockage and clear them immediately. I just used it in the morning, plugged it back in and it has not worked since. Any ideas?


... Dyson DC35 Handheld Vacuum

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.


Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy


Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.


Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum

I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.


Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums

I have a mile tt2000 that works fine up to 1300W but if I crank it up higher the motor decreases and increases speed every couple of seconds. I have changed the bag and filters and done the usual cheCks for blockages but can find nothing amiss. Unusually when it is running and I block the intake it will run at full power but as soon as I clear it the motor "hunts" again. Any ideas.


... Miele Cat & Dog 326i Bagged Canister Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

My dyson has started to give off an acrid smell when I use it. I have checked all areas for blockages, cleaned the removable filter and removed all hair from the brush but this has not helped. I am worried the motor is getting hot in use. Whats the best thing to do next? Thanks


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Bissell 2x Turbo 9300 shampooer. It won' spray from the carpet/floor position. I re-booted it and checked for blockage - nothing. I flushed the hand attachment and got it to spray some water but nothing from the carpet area.


The heater is glogged trust me. It is the size of a dollar bill with seven screws. take it apart and clean the water path also take a small drill bit to the ports of the heater. ... Vacuums

I have cleared the vacuum hose and the attached motor unit. I cannot get the brush going. What else can I do? I have also checked the connections.


Make sure that the belt is on the unit properly not twisted or broken. Also make sure that the brush is set into place correctly and not rubbing on anything else. If both check out fine then the motor is not spinning for some reason and you will need ... Vacuums

Assembly I disassembled my miele s7210 because of a blockage. Fixed that but now I can't re install the rear wheels properly.


The gears on the rear wheel assembly have to be aligned properly before they can be fastened in place, otherwise the rear axel will be crooked and and will not sit level. Your post is from 5 months ago, have you resolved the issue yet? ... Miele S7210 Bagged Upright Vacuum

Vacuum tube is obstructed at curve next to roller. I'm unable to clear it using a chop stick. vacuum functions when tube is used w/ attachment for small areas.


Do not give up... Now try wire coat hanger to clean out. Restriction of air flow will burn out your motor, eventually. ... Bissell Vacuums

My dyson vacuum motor is sounding very high pitched... The tubes are all clear and there is suction with the tubes not not real good suction on the beater brush area....


If you have tried cleaning other parts and cannot find an obstruction, and still have no suction, you could try this:\015\012\015\012 ... Vacuums

How do i detach hose to remove blockage? - Miele S7210 Bagged Upright Vacuum


Lift the hose out as if you were going to use the attachments. At the base of the hose there is a swivel to adjust the hose 90 degrees. Where the lower section of the hose attaches to the swivel you will see that if you give the hose about a quarter ... Miele S7210 Bagged Upright Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!


... Miele Vacuums

When my dyson dc14 hoover is on it has a strange burning smell, and a noise like air popping, there seems to be suction from beater and it spins. and definitley suction from extension. Filters are clear and no blockages. Is it the belt I don't think it is. or motor ? Grateful for any advice.


It could be the belt. However, the popping sound does have me puzzled. The popping could be coming from a partially broken belt slapping against plastic.Jim ... Vacuums

My Hoover Turbo has the power and motor works well but there is no suction power. I have taken all steps to ensure that there is no blockage in the pipes. I live in the Benoni area and would like someone trustworthy to repair my machine as it is only just about 1 year and 9mnths old.


Remove the screws from the funny looking thing on the back (about 10 philips head screws) and remove the blockage from the big hose. Don;t stop working on it until you are absolutely certain there is no blockage. You may need a long screw driver an ... Hoover U5396-900 Turbo Power Vacuum

Making high pitched squealing noise and motor is hot...cleaned out brush area and made sure hoses were free and clear too..noise is coming from the brushes because when I use just the wand, the noise disappears


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

I have an older model fantom vacuum (model TH56SK 00) that I was given without the manual. It is whistling and stamped on top is "whistle = blockage check manual" which of course I can't do, but I need to find and clear the blockage. I need to clear the blockage now, but would like to obtain the manual for future issues.


... Vacuums

Whinning sound in motor area


Lubricate the motor bearings! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Miele S7210 on/off switch jammed - Miele S7210 Bagged Upright Vacuum


... Miele S7210 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0515 seconds