Having problems with your Miele S7210 Bagged Upright Vacuum ?

When the brush is on it won't **** properly

\015 When the nozzle is on the hose sucks properly, but when the brush is on there's so little suction it does not pick up from the carpet properly.\015

Answers :

Look for blockage carefully as the unit does not know which you have attached.
Repair Help & Product Troubleshooting for Miele S7210 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.


The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Wont suction cleaned the brushes, tank is on properly. Must be internal clog, how do i fix it?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Brush wont spin, belt is perfect


It sounds like the motor that spins the beater brush is burned out,If it is under a yr old it should be covered by the manufacturer warretee. Find a Hoover service center that does warrentee repairs. ... Hoover U8188-900 Bagless Upright Vacuum

Brushes still wont turn


I had same problem and it was the turbine assembly. Part was only $28 but with labor it cost me $140 total. Plus it took over 5 weeks for my vacuum repair shop to get the part. In hindsight, I would have just spent another $100-$150 dollars and bo ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.


I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?


Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

DC07 brush wont spin on bottom, took all apart and wont work


Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brushes won't turn. have gotten out all thread etc, wound around the brush. have put vacuum in proper position and turned on the brush button


The brushes are usually driven by a belt that connects to one of the ends. They break. Check to see if yours has. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.


Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin


The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand


In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

THE BRUSH WONT SPIN AND THE SOLUTION WONT COME OUT


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I need a new brush bar, The end (plastic) brokeand the brush wont roll!


You can try your local vacuum shop or look online at either eBay or amazon.com. There are also websites like govacuum.com or vacpartswarehouse.com Here is a link: ... Dyson Ball DC24 Bagless Upright Vacuum

The brush wont turn


Make sure that the carpet selector is on carpet setting not bare floor. It only spins on carpet setting. If carpet setting is engaged and still doesn't work you need a new clutch assembly. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush wont turn on my dyson....only had for 4 months....what do I do with this piece of crap?!?!


... Dyson DC39 Animal Canister Vacuum

My bissell Proheat will not spray any liquid on the floor, the brushes are working properly, my attachment hoses all work properly, there is just no liquid coming out to clean the floors, any suggestions...?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 


For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum

The beater brush wont spin because the brush roll is always in the off position. Moving the carpet/hard switch doesn't turn it on.


Hello : \015\012\015\012Try this please : \015\012\015\012 Switch the carpet/bare floor dial back & forth 5 times, ending on carpet. Tilt the handle back as if to vacuum upright & lay the vacuum on its side so it is resting ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0443 seconds