Having problems with your Miele Vacuums ?

My nearly new Miele S710 vaccum cleaner just revs like mad when you switch it in but you get no suction. Could there be a drive belt between the electric motor and the vaccum pump that has come off or broken? How can I get at it, if this is the case?

Answers :

\015\012Yes this could be a case due to which there is no suction. I am posting an article which gives you a detailed description of how to open it and repair the internal parts.
\015\012Let us know if you have something more to know else accept the suggestion.
\015\012Thank You for contacting Fixya.com
Repair Help & Product Troubleshooting for Miele Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My nearly new Miele S710 vaccum cleaner just revs like mad when you switch it in but you get no suction. Could there be a drive belt between the electric motor and the vaccum pump that has come off or broken? How can I get at it, if this is the case?

Hi,\015\012\015\012Yes this could be a case due to which there is no suction. I am posting an article which gives you a detailed description of how to open it and repair the internal parts.\015\012\015\012 ... Miele Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

How to install the belt on U8188900. It has a cam on the electric motor where the belt gos and there is a center looks like a pully and the part where it fits on the brusher. How do you get the belt around the center pully?

... Hoover U8188-900 Bagless Upright Vacuum

How can I get to motor drive on g4 does it have a belt

The power drive has a geared belt on the end on the armature which operates the power drive. The power drive has been out since 1990, and I have yet to see a bad drive belt in 1000's of repairs. The drive unit itself will fail very infrequently, and ... Kirby G4 Bagged Upright Vacuum

Belt OK but no drive to main brush head. How do you get into the motor compartment to have a look?

There are in fact two belts on a DC14 - one connects the motor to the clutch, the other the clutch to the brush bar.\015\012\015\012Have a look at www.dysonmedic.com. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?

HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode

... Hoover Vacuums

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.

Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

Motor whined loudly. Vacuum failure. Suspect motor failure. Hoover.com doesn't list a replacement motor. Drive also failed - could be secondary belt HOOVER U6323- Power Drive Bagged Upright Regards, Jeffrey

Hello, funI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Change belt How do I change the belt. I took the bottom off and removed the roller but can't get the rest apart to get to the place to hook the belt on the the drive.

... Hoover U4270-930 Vacuum

Dog hair gets caught all the time in the belt drive spool, is there a fix for this other than having to pull it out all the time by hand? I have replaced the belt and the brush but this hasnt solved the problem and the belt moves so slowly and I get the loud whining/grinding noise too.

It could be either the clutch, the beater bar or the brush housing. I have included links to each parthttp://platinumvacuum.com/dyson-dc07-dc14-clutch-assembly-900252-04.htmlhttp://platinumvacuum.com/dyson-dc07-dc14-brushbar-assembly-9041 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

When I sart to run my bagless vacuum, it runs for a second and then shuts off. I replaced the belt and the filter. The repairman told me that on bagless vaccuums, the motor and bearings get clogged w

Take the brush roller off and on the ends are the bearing caps.try to take those off and clean the bearings ,carpet strands and hair will cause that.after you do that make sure the roller turns freely if not then the bearings might be bad and if that ... Vacuums

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...

Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

I'm trying to pull the fan drive of my vacuum so I can get to the motor but Ican not seem to get it off. I was wondering if there is a release switch or something that is preventing me from doing this. Also the motor seems to be burning but I think it's because ther is something in there clogging it up.

Check to see if it has reverse threads, Most do ... Vacuums

Help!!!! i have an older model of the dirt devil bagless quick vac. and it has been working great, just last week i was vaccuming my bedroom and i accidentally sucked up a string belt that goes with one of my capris. and today i emtpied out the dirt cup but it seems the the string belt that was sucked up is not within my reach and whenever i start the vaccum i get this distinctive noise that i've never heard before. help.

It's likely wrapped around the brush\015\012pull out the roller and un tangle it ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Is there a motor pulley for the brush drive belt on a bissell 3750 upright, or does the belt just ride on the motor shaft?

Just on the shaft make sure there is no hair or threads on shaft and where belt goes on brushes ... Bissell 3750 Lift Off Bagless Upright Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.

I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean

... Panasonic Vacuums

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?

I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!

... Oreck Vacuums

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.

The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0877 seconds