Having problems with your Miele Vacuums ?

Miele brush bar not spinning

\015 Its a miele s7210, when i press the button to power the brush bar, nothing happens, it used to turn on a motor that spins the brush bar?\012\012thanks\015

Answers :

Either the touchpad is defective, or the motor is bad.
My miele does the same after a few minutes. I have now deduced that the brush rollers stop because the motor gets hot. The suction part is fine. So why is this brush roller motor overheating?
Repair Help & Product Troubleshooting for Miele Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Miele brush bar not spinning

Either the touchpad is defective, or the motor is bad. ... Miele Vacuums

Miele silver moon power head brush bar not spinning but spins sometimes

... Miele Vacuums

Is it possible to remove the brush bar from the housing of a mieleTurbobrush STB 205? The brush bar is not spinning due to been dirty and clogged and needs to be removed for cleaning. Is it possible to remove the brush bar????

... Miele 06271980 STB 205-3 Turbobrush

I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the

Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. ... Bissell Vacuums

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.

Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.

The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The bar brush does not spin. I opened the vacuum head and the drive belt to the bar brush is loose. I don't see how you remove the slack from the belt.

You have to have it in the carpet setting in order to put pressure on the v-belt. there is no way to tighten up the v-belt, but i would try to replace the big flat belt. if you haven't changed this belt in over 6 months, i would change it. ( on avera ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

5 yr. old Miele s514 Turbo plus's power nozzle brush seems to disengage temporarily, stopping the spin. Then it seems to re-seat itself after a few seconds, then starts spinning OK. I keep the nozzle brush very clean, so there is no hair or yucky stuff to cause it to jam. Please help.

I had a White Pearl with same problem. As I moved the hose/wand the brush motor would start stop. Find out where the circuit opens up by holding one part and moving the part that connects to it - 1) where the hose plugs into the cleaner, 2) the swi ... Miele S514 Solaris Turbo Plus Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?

Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums

Cleaned the brush bar but still not spinning DC14 Dyson

The belt is broke. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC 28 brush bar wont spin

... Dyson DC28 Animal Upright Vacuum New DC 28 Animal

"brush bar spins erratically"

Belt needs to be replaced, it has stretched to the point that under load, it won't turn the brush roll like it should, so I would advise replacing the belt. And while you are doing that, check the brush roll and make sure the ends turn freely, if no ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

The brush bar no longer spins when I turn it on

Hi there,I'm sorry to hear you're having difficulties with your Dyson. I can't provide specific advice as you haven't stated which model of Dyson you own - but if you call us free on 0800 298 0298 (UK), or 1-866-693-9766 (US), we should be ab ... Dyson Vacuums

Brush bar not spinning when set to high or low on carpet

1) adjust the belt, see for broken or worn, and replace2)see for brushroller obstruction, and clean it and repair3) see if the brushroller without belt run smooth, otherwise repair and fix it.Lubricate.4)See if the motor run without load( ... Vacuums

The brush bar wont spin on my dyson dc 25... i

Hi its Darran at Dyson.Simply switch the machine off and stand it upright. Press the brush bar on/off switch once and then turn the machine back on. When you release the machine into the vacuuming position, the brush bar shoul ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

Brush bar can't spin

Hi There,\015\012\015\012Actually I just answered a question almost identical to yours! The belt on his model continiously snapped also. \015\012\015\012I walked him through how to check the problem, and he was able to ge ... Dirt Devil Featherlight Bagless Upright Vacuum

Miele HS03 S251i Brush not spinning

... Vacuums

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a DC 37, it's 3 weeks old. The brush bar will not spin. It spins when initially turned on but stops after about 3-5 seconds. I have cleaned it but still does not work.

... Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]

Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brush on my dc07 will not spin while vacuuming and it also smells of burnt rubber. I cleaned the brush bar and the belt is intact...

... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush bar on my brand new DC 28 has stopped spinning - it is not clogged with hair, it just stops spinning almost immediately. Is there a reset button?

If there is nothing dragging it down like clogged hair ect then usually this just means the rubber drive belt has either stretched or is too smooth to grip and properlly drive the beater bar brushes. When those happen the belt cannot get a grip and s ... Vacuums

Vax mach 6 brush bar does not spin properly. does not spin at all on lower carpet settings and also when it is being pushed forward

... Vacuums

Brush bar not spinning

Depending on the make and model the belt may be bad or if it has a clutch assembly then it has gone bad. ... Vacuums

Dyson Brush Bar Always Spins

Hello there my dco7 brush bar just spins all the time.but with it upright it stop spin,is this correct.. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0529 seconds