Having problems with your Miele Vacuums ?

Have miele powerhead seb217-2 need circuit board where can i get one

\015 Email [email protected]\015

Answers :

Hi there,
Not sure where you are from but VacuumSpot.com.au are miele authorised parts stockists. The cost for the board is $122. The part number is 5724730.
Regards
Alec
Repair Help & Product Troubleshooting for Miele Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have miele powerhead seb217-2 need circuit board where can i get one


Hi there, Not sure where you are from but VacuumSpot.com.au are miele authorised parts stockists. The cost for the board is $122. The part number is 5724730. Regards ... Miele Vacuums

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?


... Miele SEB 213-2 Vacuum

How does the Miele Vacuum Power Nozzle Pinion Gear get taken off and a new one put on? Is it pressed on and just need to pull off or is it screwed off. It is for the SEB217 power head


Greetings,\015\012\015\012What you need to do is screw the Pinion Gear off of the power brush. This can sometimes be tricking, because as I'm sure you're aware, when you twist the pinion gear to try and release it, it also spins the mot ... Miele S318 Bagged Canister Vacuum

Hi, my circuit board resistors are burnt due to my re-wiring the resistor switch. How do I fix this - S3755 wiring diagram?? need to know the correct resistors or get a new board


The only way is to get a replacement board. even the dealers are not provided with that level of wiring diagrams. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums

Circuit board i have searched far and wide looking for a circuit board for my fantom cyclone xt, so far i can't find one .. is their anyone who can can locate or sell me one of these hard to find items. i am at the end of my rope ! any help is appreciated, thank you for your time TOO SLIM


Http://www.vacmall.com/supplies.asp?Brand=Fantom&Model=Cyclone+XT ... Fantom Vacums Cyclone XT Upright Vacuum

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1


As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Need a replacement on/off switch for Dirt Devil Deluxe Model 8201 (more than 12 years old). We have the old one out. We just need a new one to replace it. Where can we get one?


... Dirt Devil Vacuums

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?


Probably needs a new hose. ... Vacuums

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?


HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

My circuit board has a short on the soldering for the DC rectifier that supplies the carpet cleaning motor. Where can I order a new circuit board. Miele S251i


Just a suggestion, but you could try to re-solder the connection on the board. some of the circuit boards did not have enough solder on the board coming from the factory. That being said, if the component is damaged due to the burning, I ... Miele S251i Plus Bagged Canister Vacuum

How do I get a replacement belt for my DC 17? We sucked something up and broke is so I do not care if it costs anything, I just need a belt for the beater. How do I get one? unfortunately my wife also through out the old one with a part number on it,....


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?


Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Euro-Pro model#EP187H. I need a new filter, can I order one from your Company? Please let me know, or if you don't have one where might I get one. Thanks, Elaine Foster


... Euro-Pro Vacuums

My iron is dripping water my model number is dz6080 focus do i need a new one? It is coming out of the bottom when it is sitting upright. my ironing board is all stained and actually my floor is rusted from when I fold up my board and put it away it drips from the ironing board. I paid alot for this model.


... Rowenta Vacuums

I need a rocker switch for my Shark Navigator. Where can I get one. Thanks Dan - [email protected]


... Euro-Pro Vacuums

I have a Dirt Devil rechargable stick vac that has lost power. Does it need a new battery and if so, where can I get one and how much is it?


... Dirt Devil Vacuums

My samsung quiet storm modl 9068G needs a new brush in the power head. Where can I get one?


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I am trying to install a train air horn. i bought a viair compressor for it. the horns themselves have a 12 volt hookup going to what i believe is acting like a solenoid. when charged, you complete the circuit and walah, the horn blasts. the problem im having is when the compressor is building pressure, the air horn is automatically putting out a dull sound, getting louder as the pressure gets more and more. it sounds like its out of one horn however. it is doing that without the 12 v hookup. is


Hi! just a tip regarding the sound that comes up when building pressure. Is there a gasket or rubber seal on the horn? You may need to replace this for it may be worn. The air may be coming out of the worn seals resulting to sound even when not trigg ... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Need a cheaper alternative shampoo for kirby vacuum system. Has to be an encapsulating shampoo. Kirby shampoo is too dear and only does one room per bottle. Need to know where to get some in australia as the postage from america is 3 times the price of the shampoo. thanks


Look up your local janitoral supply companies in the yellow pages. Encapsulation shampoo should be readily available in AU. \015\012\015\012Here is a list of websites to check out: \015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I need to get a belt for my Eureka up right Model # 2271 what is the number of the belt and how can I get one?


Http://www.vacuumcleanershop.com/Eureka-Belts.htm?gclid=COSGj7qs05ICFQG5PAodmiJtlA ... Vacuums

I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.


Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?


There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0865 seconds