Having problems with your Miele Vacuums ?

Miele vacuum hard to push on carpet

\015 Hard to push on carpet\015

Answers :

Repair Help & Product Troubleshooting for Miele Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Miele vacuum hard to push on carpet


... Miele Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Dirt devile featherlite vacuum pushes extremely hard on high pile carpeting


The dirt devil featherlight has a automatic height adjustment for carpet and bare floors.check the wheels and see if there is something wrapped up around the wheels ... Vacuums

The vacuum is very hard to push on carpeting even when on hard floor level.


... Hoover Tempo Widepath Upright Vacuum - Blue

Vacuum very hard to push on carpet. How can the roller be adjusted to accommodate the thickness of the carpet? Oreck XL Upright Model no. U4140HHPKCOST Serial No.: 4140CSTDC002218


... Oreck XL® Classic Bagged Upright Vacuum

My vacuum has good suction but i can hardly push it across my carpet. any answers????


Is your brush roller turning,that would cause it to be hard to push .the brush roller helps it walk across the floor.if your brush roller isn't turning then your belt is broke or the brush itself siezed up.unplug the vacuum and try to turn the brush ... Kenmore Vacuums

Sharp vacuum, model ec-tu2607 pushes hard on carpeting


... Sharp Twin Energy EC-TU2607 Vacuum

New windtunnel bag vacuum worked fine for about a week but now is unbelieveably hard to push at same setting on same carpet as before.


The self propelled unit might have broken, their is a metal wire that helps make unit work correctly ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Which is better Miele vacuums or Dyson - we want a motor/power head for carpet cleaning and hard floors


I prefer dyson myself ... Vacuums

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My vacuum is very hard to push and pulling back causes rumbles on my carpet.


Check the sole plate is clean of any dirt or worn brushes..http://media.dyson.com/downloads/UK/floorcare/Manuals/dc27_all ... Dyson DC27 Bagless Upright Vacuum

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

My vacuum is really hard to push on carpet. Is this normal?


You can adjust the hieght to make it easier to push. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

Difficulty to operate a vacuum cleaner on Smartstrand. I have a Miele which is a great vacuum cleaner. But it cannot move smoothly over this carpet. One's back is under stress trying to vacuum this carpet. The carpet is thick and luxurious and won't rot but it is hell to vacuum.


... Vacuums

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

When pushing foreward the vacuum is hard to push and if pushed on to hard it will turn over on itself.


My dyson dc17 animal had become nearly impossible to push on carpets. sure enough i found that my roller was warn down to nubs (vacuum is probably 8 years old, and gets used nearly every day) I replaced the roller and WOW! it feels ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.


Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

The dial that you turn on hard floors or carpet,when in carpet slips by and then go past and makes a awful noise will not stay in carpet position to vacuum on carpets.


... Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Miele s7000 I first got the vacuum and used it for 20mins then the vacuum just lost the suction, the brush works but it just push the dirt around the house and I can see the dust and dirt flying around.So, I thought maybe the bag was fulled so I put the new bag in but still pushing the dirt around. What's wrong with it?


... Vacuums

My Oreck XL 7000 is hard to push through a modest pile carpet. They gave us a shag attachment but all that does is push the carpet down. It is not ususable for us with bad backs etc.


... Oreck XL2200 Bagged Upright Vacuum

My windsor sensor 12 inch vacuum is to hard to push. I bought a new one and its doing the same thing. My vacuum repair man says he cant fix the problem. My shoulders are sore from working so hard. Help


It\\'s possibly the type of carpet you\\'re using it on. The sensors use the brush speed and the amount of air flow to determine carpet height. Some berber, and tweeds make these things horrible to push. We sell sebo, who make the windsor and we\\'ve ... Windsor SR12 Sensor Bagged Upright Vacuum

My Dyson is getting stuck when I am trying to vacuum. I try to force it by pushing hard, but it is stuck. Weird.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0733 seconds