Having problems with your Miele Vacuums ?

How do I rewire a miele flamenco II lamb ametek 115923 motor without the male plastic lead ?

\015 I have a Miele Flamenco II vacuum with a new Lamb Ametek 115923 motor. How do I rewire the motor into the female plug (located inside the vacuum body) without the original male end lead ?\015

Answers :

Repair Help & Product Troubleshooting for Miele Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I rewire a miele flamenco II lamb ametek 115923 motor without the male plastic lead ?

... Miele Vacuums

I have a simplicity f3500 and while vacuuming the plastic part of the motor with the blades broke off, (the end plastic part of the motor....where can I buy that part without replacing the entire motor? Jodi

SURBAN VACUUM 315-4543111 ASK FOR KEN ... Simplicity 7850 Premier Bagged Canister Vacuum

Do i need to do anything special when replacing the brushes in a lamb ametek 117500 motor? It looks like I can just remove the old brushes and insert the new ones. Is it this simple? Will the motor work again? Thanks

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758676\015\012Generic problem for all Vacuums\015\012Do I need to do\015\012Posted by edkraynak on Jul ... Vacuums

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther

... Kenmore Vacuums

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.

... Electrolux Vacuums

My Sharp EC-l2TWT4 throws belts and I noticed the motor shaft was not running straight. My wife took it to my local dealer in Brainerd,Mn and they said it was fine.So I took it apart and found the plastic motor housing had melted at some point letting the motor twist out of alignment. Other than this, everything works great.Can I order this plastic housing piece somewhere?

I checked the schematics for that model and the motor housing for that model is no longer available. Your best bet is to either attempt to find a used part or trade it in and get a new unit. Sharp no longer makes any vacuums or parts which makes thes ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!

... Oreck Vacuums

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.

... Electrolux Vacuums

Bissell Powerwash Proheat. model 1698-j, 220-240v, 50/60Hz, 1200-1400w. Motor stopped suddenly (ident label specifies type Ametek 119464-02), supply inline fuse at motor ruptured, fuse replaced but motor sparks like an angle grinder at armature and blew replacement fuse. Where can I obtain a replacement carbon brush set for the motor. UK based

... Bissell Vacuums

Replacing the Oreck vacuum cleaner motor with a generic Ametek motor, the wiring terminal are different and I need an electric diagram

... Vacuums

Dyson DC07 Vacume cleaner trips on thermal after 10 min motor not excesive hot resets after 15 min has been doing this for the last 3 mths. Could it be faulty thermal or motor overheat how can I check without changing motor

First, check both filters on that unit. the premotor filter on the side, and the hepa filter underneath the canister. if those filters are clean move through the suction channel and look for a clog or obstruction. also make sure the canister is clean ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Not exactly a blow gun. Convertible blower/vac - Sears Craftsman. Wire broke off ONE brush in the motor. Paid about $90 for the vac - Sears lists the WHOLE motor as one part - $88. Have requested brushes (they are provided with a lot of my 'cheap' Harbor Freight tools) but no go. Just get the canned reply - buy the whole motor. Actually got it working again... CAREFULLY drilled and tapped a 4-40 screw into the brush and soldered the lead to that... Always a way, isn't there?

... Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Brushes in motor are arcing badly and motor only occasionally will start. How do i remove the motor brushes for replacement. (from the green plastic case)

This is kinda of tricky. need to know what kinda of vacuum it is first. However if you get it apart. To fix this problem the armeture brass needs to be cleaned & you should replace both carbon brushes. Should be cheap to fix if you are up to it. ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

My husband threw out my motor bag for my Delonghi Wet and dry M-31. Can I run the vacumm without this protecting the motor?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=538790\015\012\015\012Generic problem for all Vacuums\015\012My husband threw out my\015\012Delonghi Wet & Dry M-31 ... Vacuums

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

Does not pick up, no vaccum, motor runs, no blockage, should feel suction on hose outlet without hose hook up. Paper filter missing over cloth filter. float overload ball free, seal on section good no leakage. Maybe bad motor but runs.

Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Minuteman C82906-01 HEPA Vacuum Vacuum

My vacuum cleaner stopped working without any smell or anything. I took to a local repair person and he said nothing wrong except motor he tried new hose, etc. And he wants to change the motor..

I would go with the repair man and what he says. They know what they are talking about and if he was trying to rip you off he would have suggested many things to repair and then after you had spent a few hundred he would have told you to replace the ... Kenmore 25512/ 25513 Progressive Canister Vacuum

On the piece that covers the brushbar and motor (the clear plastic piece that has the dyson logo), it looks like a small plastic ridge that holds the cap for the brushbar snapped off. Would too much wobbling of the brushbar cause it to turn on and off? The switch seems fine.

In theory, yes. If the brushbar isn't held firmly, then the belt isn't running smoothly which puts more strain on the motor. This can cause the motor to get hot very quickly which will trip the thermal overload protection. \015\012\015\01 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic

... Vacuums

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl

There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.

Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Electrical cord electric cord connection to cannister boby on filter queen is fixed by a plastic grommet or connection - how does this go into place without breaking or forcing plastic part?

It has a **** shell like closure on the inside and can normally be popped out by squeezing with pliers. It will have a slightly oval appearance, you must squeeze it round and pull. ... Filter Queen Majestic Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0765 seconds