Having problems with your Morphy Richards 42242 Elite Jet Stream Steam Generator With Ceramic Soleplate - Charcoal And White ?

My iron keeps tripping electric

\015 Every time i plug it in it trips the main power supply\015

Answers :

Repair Help & Product Troubleshooting for Morphy Richards 42242 Elite Jet Stream Steam Generator With Ceramic Soleplate - Charcoal And White

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Keep getting an electrical shock when using iron. is it possible to replace cables??????

It sounds like there is a bear wire inside the iron touching the case causing the shock. You have to take the iron apart and look for wires with cracked insulation and replace them or wrap electrical tape around the bear part. ... Vacuums

Conair does not sell the springs for their curling iron. Mine keep breaking and I do not want to keep buying a whole new curling iron just because the wire spring has broken. Instant Heat curling iron, model number CD8sWCS. Do you know where I can buy these springs or how I can improvise with something that will work almost as well?

Hi,\015\012\015\012The best thing I know of is to take a wire bread bag tie....take the paper off of it so that you just have the wire part... twist this around the two ends of the wires where it broke...this will contect the two wires an ... Conair Vacuums

I have a Bissell 9200e that has only been used a few times. When I have gone to turn it on it made a loud crack and then tripped the electricity and everytime I turn it on it trips the electricity. Any ideas what may be wrong?

Check plug to exclude short there, if none its an internal short circuit and machine would need opened to find it so if only used a few time return for under warranty repair. ... Bissell 9200 Upright Vacuum

Installed new VX550C central vac unit today. Breaker at electric panel trips after unit is ran one time. Reset, use once, then breaker trips again at next use.

... Vacuums

The Dyson DC21 power head keeps tripping out. The carpets in the house are medium to low pile. It even trips out over hard surfaces. Could it be the resistor in the power head is to weak or faulty.

... Dyson DC21 Bagless Canister Cyclonic Vacuum

My swan steam generator iron s15040n is showing a push button when it is turned on. im pushing the button but it continues to say push and keeps beeping. the iron wont turn on at all. please help!!!!! thanks

... Vacuums

Breaker keeps tripping

... Broan-NuTone Vacuums

My dc24 has power makes the right noise but when released from upright gives a burning smell an trips the electric out . Is this a repairable problem? Do you think its covered by gaurantee?

... Dyson DC14 Bagless Upright Cyclonic Vacuum

It keeps tripping the breakers or the GFI outlet.

Try different outlets in another room to see if that dosent help you may have a shortin the cleaner but i think you may be overloading the breaker ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My polti keeps tripping my mains off

... Polti Vaporetto 2400 Canister Steam Vacuum

Fuse keeps tripping

Check the power cable for splits or brakes ... Hoover Vacuums

Vax 2000 trips electrics

Try the reset drive belt brush button - you'll find it underneath the main power switch on the handle. Also check the brush isn't clogged, by the sole plate by tipping it over and undoing the screws on the bottom place where the beater bar is. ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

My Shop Vac (Brand) Mdl#934-16-11 keeps shutting off while I'm dry vacuuming. I can turn it back on then it will shut off again. The filter is spotless, so that's not the issue. There isn't any reset buttons. The only thing I can think of is that the float for wet vacuuming is somehow being sucked up causing the the motor to be tripped off. The vacuum is only about a year and a half old and used only sparingly. Help!

... Vacuums

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?

If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

Cyclovac dl-200 sv control card blew,why? Changed card installed new card different rev. ,rev.c instead of rev.e fuse on card keeps tripping vacuum only operates on one speed high.

... Vacuums

Can't find the manual for Biddeford electric blanket (warming blanket) '08. Controls are acting up. One side keeps turning itself off and says 'E'. I'm assuming this means error. The other side only registars '8' and can not change or turn off unless I unplug.

... Vacuums

I just bought my edmark steam brush but didn't able to watch the guy selling it. Does the iron board really not coming hot? do I need to keep on pressing the steam button while using it? please somebody answer me/ thanks

... Vacuums

I have 2003 Coleman Westlake Pop Up Camper. I have electrical problem. Replace circuit breaker and ground fault. Went camping, everything running fine the all of the sudden all power cuts off. Breaker did not trip, ground fault is fine. What could be the problem ? Is my converter bad ??

... Vacuums

I need to get to the internals of the machine in order to retape the electric wire that originates inside. I have removed all of the visible external screws that are keeping the 2 sides together but it still will not open. It is a Euro-Pro vacuum model ep 601. Can you help?

\015\012\015\0121. \015\0121 Lower handle of vacuum and flip\015\012over so that it lies flat on floor upside down.\015\0122. Twist 3 plast ... Euro-Pro Vacuums

How do I undo the torx screws that hold the Polti 2400 Steam Cleaner (Polti Vaporetto 2400) together? There is an electrical fault and I will have to strip it down to investigate.The house RCD trips when the item is plugged in, I suspect over the years the cable has been twisted and is now shorting.

Hi you need the torque driver no 20 the problem I had was the 2 middle screws luckily a friend of mine had a set of torque allen keys they were long enough to remove them hope this helps if you llived in the North East I would have let you borrrow th ... Polti Vaporetto 2400 Canister Steam Vacuum

We have an MC-3003 vacuum cleaner which keeps cutting out. We've changed the bag, but the problem still occurs with a new bag fitted. Could it be an electrical fault and is the machine repairable?

... Panasonic Vacuums

Dyson 21 power head keeps tripping out on low pile carpet I've completely cleaned the powerhead

... Dyson DC21 Bagless Canister Cyclonic Vacuum

My SEBO vacuum cleaner keeps cutting out which seems to suggest an dodgy electrical connection...any ideas ?

If it just cuts out then comes back on after a while, it might be overheating. ... Sebo Vacuums

I have a Bissell 9400 E pro heat turbo. It's only been used 4 times, today it sounded like something blew. All my house electrics went off...( blew the main trip) I did read some place that the motor can short out and blow the PCB. Hubby and I just took it apart..( what a pain that was) We can't see a thing wrong with the board...( I expected to see something black, or damaged).... because when it blew today there was a weird smell... sort of like garlic. Question... how on this spinning earth

I have the exact same problem! Just occurred today. When I switch it on it fires for a couple of seconds then takes all the electrics in the house out again.\012\012\012Did ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0299 seconds