Having problems with your Morphy Richards Vacuums ?

My morphy richards premair 1800W has suddenly lost suction. I suspect there's a hole somewhere in the hose, and I need to replace it - but no-one seems to have the parts. does anyone out there have a solution


Answers :

Repair Help & Product Troubleshooting for Morphy Richards Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My morphy richards premair 1800W has suddenly lost suction. I suspect there's a hole somewhere in the hose, and I need to replace it - but no-one seems to have the parts. does anyone out there have a solution


... Morphy Richards Vacuums

I need to replace the brushbaron my DC17 Animal model Dyson. It's almost four years old. I can't find the correct part number on the Dyson Website and I can't seem to find a Dyson repair center in Albuquerque, NM. What are my alternatives? If I can't service this machine without returning it to Dyson, I won't ever buy another one.


Hi,\015\012\015\012The original Dyson part number for the brush bar (often called brush roll) is: 911961-01\015\012\015\012If you type the above part number into Google Products (click link below) you will get a list of suppli ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have cleaned the filters on my dust buster. The vacuum works for a minute then the battery seems to wear out and the power weakens until it stops. How do I replace the battery on this vacuum? Do I need just one 9.6V battery? What screws do I loosen to insert the battery? I can't find my instruction booklet. Tank you for your help.


... Black & Decker 15.6 Volt DustBuster Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Hoover U6433-900 brush turns intermittently - Belts are in tact but the lower thin one seems loose. How often do they need to be replaced?


The rollers on each ends get tangled with hair etc...\015\012causes resistance. Give it a good clean up. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available


Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

Need a replacement on/off switch for Dirt Devil Deluxe Model 8201 (more than 12 years old). We have the old one out. We just need a new one to replace it. Where can we get one?


... Dirt Devil Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1


As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!


... Dyson DC05 Bagless Canister Cyclonic Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I think I need to replace the main battery in my small floor vac - the one that can be hand held like a dust buster or work like a small floor vac. I need to know how to remove the battery and replace it with what kind of new battery..


I see my sense of humor is not appreciated...it was only a joke. Anyway, here is what you do: First, slide the battery cover off the bottom of the hand held unit. Remove the battery from the motor housing by pressing the tab on connector “A&rdq ... Vacuums

I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks


Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?


Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Don't have one, need access to one, can't seem to find one online


Ebay... ... Vacuums

Replacement wheel I broke the wheel on my bissell upright model 3760 and need a replacement wheel and possibly an associated side molding. I can't seem to find replacement parts such as these- any suggestions?


The rear number is 2036627, there is no side casing, you would have to replace the whole back, which Bissell isn't making avaiable. But o get the wheel, you might try bissell.com and see if you can order direct, or try a local repair shop to see if ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

One of my Levolor double-honeycomb blinds is no longer level (one side goes up faster than the other). Another of my blinds (same brand, model) seems to have broken, with one side no longer rising. Both blinds are about 9 years old. Is there any way to fix them? Or, does it make more economic sense to replace them? Thank you!


Hello,\015\012\015\012This problem is a common problem on this device, there are many people\015\012who are searching for the answer on what to do and what are the causes\015\012of this problem. The answer to this is still not clear. ... Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no


... Vacuums

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

Power head on my Electrolux Epic stopped working. Do I need a new one or could there be a part that needs replacing. Can I open it to see?


Have you tried pushing the reset button? I'd try that first. If that doesn't work it could be that the belt is broken. The motors don't go out very often on those. ... Electrolux Epic 6500 Vacuum

I just bought a Hoover Power Drive Concept Two Electronic vacuum from the thrift shop. It only needed two belts and seems powerful. But i don't understand what the small red button on the handle marked "Release Drive" means. Thanks for any insight! Anything else i need to know about this machine? Is it a good one? Are there high-performance bags available for it?


The U6311-903 is a self propelled vacuum. The the small red button will stop the handle from moving back and forth, which makes the machine go foward and backwards. The red button disengages the self propelled feature. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

I just bought this vacuum at a second hand store. My girlfriend told me to grab it as it such a quailty product. How ever I can't find a model number or anything else. I need a manual please. Does it take bags? Do I need to replace the filter or just wash the one I have? It is black and silver, cannister. It also says big gary's vacuum system warehouse in surry British Columbia, Canada. It also says to use filter pow-r-nozzle 96. I have no idea of the year.


I suggest you google what you know. I dont think anyone here can suggest where you can get a manual for a machine you dont even know the name of.\015\012\015\012You ask about a bag ... I dont know ... is there one in it now? You ask abo ... Vacuums

I own a Eureka Optima 437 and one of the rear wheels are broken and cannot find parts for this. Where can I find parts for real wheel? I have a rear wheel that came off too. The wheel seems fine, but the plastic base that the wheel clicks onto on the underside of the vac seems to have cracked. I need a new plastic bottom. Any ideas?


Called Eureka Customer Service and ordered another part. They are mailing it to me free of charge!No more problem. ... Eureka 431A Optima Bagless Upright Vacuum

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?


HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0772 seconds