Having problems with your Nilfisk Family Vac Bagged Canister Vacuum ?

Need directions on how to remove old cotton filter and install new one and same for HEPA filter on Nilfisk GM/GS 80.


Answers :

This link should help:

http://www.fixya.com/search.aspx?cstm=0&_s=Nilfisk+GM%2FGS+80+instruction+manual

Jim
Repair Help & Product Troubleshooting for Nilfisk Family Vac Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need directions on how to remove old cotton filter and install new one and same for HEPA filter on Nilfisk GM/GS 80.


This link should help:http://www.fixya.com/search.aspx?cstm=0&_s=Nilfisk+GM%2FGS+80+instruction+manualJim ... Nilfisk Family Vac Bagged Canister Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Our problem with our Rainbow E Series is that it has sucked water up and blown it out through the lower part of the hepa filter, making the filter wet and dirty. This had happened before and the repair shop did not see any problems with the machine, so we replaced the filter and were very carful not to overfill the tank and to change the water often. Now it has happened again and ruined another filter. Do you know what could be causing this issue? Can the filter be cleaned or will a new one be


Thank you for allowing\012us to help, please respond with further questions and concerns\012\012Spanish speaking\012available for all problems\012\012 ... Rainbow E series Canister Wet/Dry Vacuum

Want to sell used Fantom Lightening parts and one new hepa filter


I would like to buy the wand of the vacuum. how much do you want for it with shipping?\015\012\015\012email: [email protected] ... Fantom Vacums Lighting Canister Vacuum

Z8220 STOPS WORKING HEPA FILTER LIGHT FLASHING & NEW FILTERS INSTALLED


Check your hose for a clog, id even check from where brushroll is at bottom to the end of hose. sounds like that could be your problem. ... Electrolux Vacuums

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?


Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.


... RTO Vacuums

Vacuum shut off immediatly when suckchen is applied new bag hepa filter removed plus hose is removed when i put my hand over suckghen side it shuts down


Sounds like motor overheating due to fault within....Operates a thermal overload, This could also be faulty ... Electrolux EL7055A Bagless Canister Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

How to install the back hepa filter on canister vacuum cleaner. We are not sure which direction the air flows and therefore which way the arrows should point. Should the arrows point into the vacuum cleaner or point towards the outside?


The arrows in this case should point out of the machine. not into the machine. This is because you want the black rubber seal to seal on the machine and force the air through the filter. Good luck. Mark ... Kenmore 25512/ 25513 Progressive Canister Vacuum

HEPA filter installation direction - Kenmore 22313 Bagged Canister Vacuum


... Kenmore 22313 Bagged Canister Vacuum

I have an aerus electrolux guardian canister vacuum. The cord was damaged but the retraction winder is still fine. I have ordered a replacement cord but I have no idea how to remove the old cord and install the new one. Am I over my head?


The winder is activated by a coil spring located in a drum. The drum transmits the power from the wire with 2 circular contacts. To replace the cable you must dismantle the case to access the drum, take the spring pressure out carefully as to not let ... Vacuums

I have a clearviewII model 3576-3 and the handle release lever is broken. How to I remove the old lever and install a new one? Thanks, Pat


... Bissell Vacuums

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.


Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I just received my Hepa filter in the mail today. Product #XSH621 - Hepa filter for EP619 & EP621 :005-04 When bought my vacumn, I was told that the filters were free and all I do is pay Postage. Today I received one filter and it lookes like I got charged the postage for two filters. The packages slips: One stated order #11152282 The other order # 1151940 If I get charged for two I expect to receive two. Can you help me with this matter or where can I go to get resolution. Catherine Fantini e-


This isn't really a problem that can be fixed here on Fixya rather than advise you as a buyer. You'd have to contact the people/company you have purchased the filters from and take it up with them regarding the postage. Hope you get a decent reply. ... Euro-Pro Vacuums

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.


Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

HEPA Filter My vacuum came with a sponge over the filter and the directions said I could wash the filter. Do the directions mean to wash the black sponge or the actual filter? Is the sponge part of the filter or is it trash? Filter F27 Dirt Devil Purpose Cleaner for Pets Upright Bagless Vacuum Model #1LY2108-000


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=618630&thid=730623\015\012HEPA Filter\015\012Posted by jenski66 on Jul 02, 2008\015\012My vacuum came with a spon ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

Kenmore Elite 721.66463500 Microwave died. Didn't even notice until I went to use it. Changed fuse and screen asked to enter the time of day. Entered the time and hit start. The microwave buzzed for 0.5sec and it blew the new fuse I installed.. put in another fuse and the same thing happened.. I measured the resistance in the noise filter. Results: L1-L2 < 1ohm N1-N2 < 1ohm L1 or L2 - N1 or N2 = 0ohms I'm thinking I need a new filter but I also was unable to measure any resistance o


... Vacuums

My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Our Electrolux Ultra Silencer Harmony Z3347 just broke down. We need a new Non-Washable O2 HEPA H12 Filter serial no 117939-03. Do you know where we can get a new filter? Thanks


... Electrolux Vacuums

My kenmore cannister vac (model 116.27514) has a slight burning odor after operating for a few minutes. We have removed the hepa filter and it looks like there is a strip of foam curled up behind the hepa filter compartment. Could that be the problem? How do we access that area? Thank you.


... Kenmore 22822 Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0933 seconds