Having problems with your Nilfisk Vacuums ?

How to take apart a Nilfisk Action Plus Vacuum to replace the motor


Answers :

Repair Help & Product Troubleshooting for Nilfisk Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to take apart a Nilfisk Action Plus Vacuum to replace the motor


... Nilfisk Vacuums

How to take apart Nilfisk Action Plus to replace spring loaded cord retriever


... Vacuums

On an old upright prolux plus, I just replaced the belt and cleaned out the brush motor, ran the vacuum for a bit, then the vacuum motor died...it's always run great. any suggestions of what to check?


... Electrolux Vacuums

How do I open a Nilfisk Action Plus vacuum cleaner?


L have a question but no answer for your question--is switch actually broken or unit will not power on? ... Vacuums

How to open a Nilfisk action plus vacuum cleaner?


... Vacuums

The thermal motor protector on sears model 116.35912 Kenmore vacuum won't reset. The manual says to wait 30 minutes and the thermal protector will reset on it's own. It appears I would have to take the vacuum apart to get to the thermal protector. Is it worth the effort or should I trash the vacuum?


... Kenmore Vacuums

My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller [email protected]


A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums

I have a Dirt Devil Upright Vacuum Model 088525B. I need to replace the power cord. How do I take the vacuum apart?


... Dirt Devil Vacuums

My hoover 600 elite is really load. I took it all apart to find the motor fan is damaged with a broken off piece which must have been vacuumed up into the bag. If I replace it sith a new plastic fan will this quiet the vacuum? right now it is tremendously loud.


... Hoover Elite U5061-900 Bagged Upright Vacuum

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?


Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

The hose,essential to the vacuum, came apart. I tried tape but to no avail. Purchased 6 weeks ago. can yousend me a replacement hose? It is a Durabrand Bagless Cannister Vacuum. your phone number on the box is disconnected. It is a 1200 watt motor and I'm assuming that VCH3301 is the model number. Thanking you in advance for any assistance.Sue Jackson


I'm sorry to inform you but we're not the right place for the replacement because are a site that provides help and we're not connected to Durabrand Bagless , So for you hose replacement concern better try asking that to the store or the person whom ... Vacuums

How to take apart wand of kenmore vacuum 116.24614400 to replace COVER #8191782 on Sears part


... Kenmore Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

I have an older Electrolux canister vacuum - model #2100 and the temperature sensor shuts down the motor. How to I take apart and clean?


Check to be certain the thermo lite is on and not the bag full indicator. The thermo detector is very reliable, but the bag fill valve often fails. If it is the thermo, check your hose and wand for blockage by dropping a coin through them,before ope ... Electrolux UltraLux 2000 Bagged Canister Vacuum

The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?


Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Vacuum motor stop working...is it worth taking it apart


The motor itself is not worth taking apart. You should be able to order a new motor. I recommend taking it to a shop for repair or motor replacement.\015\012Are you sure it's the motor, or is there a problem with the cord, switch, or other co ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

No suction After taking the vacuum apart, I noticed there is no suction at all. The motor runs, belt runs, but no suction coming through.


You have a clog somewhere in the vacuum. Check the hose and the little trap door on the underneath side of sweeper.Does the brush turn? If not, then the belt that drives the brush is broken. Replace the beltJim ... Hoover Tempo Widepath Upright Vacuum - Blue

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

How do you take the vacuum apart to replace the belt


Here\015\012is a link to the belt you need and to the manual which has instructions:Eureka 2961AVZ Belts ... Eureka 2961AVZ Bagless Upright Vacuum

I broke my kirby generation 3 vacuum cloth bag latch i found where to get the part but how do take it apart to replace it


... Kirby Generation 3 Bagged Upright Vacuum

Where can i get replacement motor for nilfisk gm80 vacuum cleaner


In the USA, refer to http://www.nilfiskcfm.com/\015\012\015\012In Australia, ask me :) ... Nilfisk Vacuums

How to take apart to replace power cord - Miele S183 Powerhouse Bagged Upright Vacuum


Hello,In order to access the cord on the Miele S183 upright, you'll need to first remove the handle from the vacuum cleaner. There is a large screw that holds the handle in place that is located under neath of the lower cord wrap hook. ... Miele S183 Powerhouse Bagged Upright Vacuum

Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.


Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1148 seconds