Having problems with your Nilfisk Vacuums ?
Need to find a repair company to service our Nilfisk vacuum in the Lehigh Valley, PA area.
Where can i find a hoover service centre in leyton or stratford in london?
Repair Help & Product Troubleshooting for Nilfisk Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Need to find a repair company to service our Nilfisk vacuum in the Lehigh Valley, PA area.
Where can i find a hoover service centre in leyton or stratford in london? ... Nilfisk Vacuums
The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?
As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Could I have a short in my cord? I can vacuum & then when I move the canister it shuts off, if I wiggle the cord it will turn back on. This last time, it just revs like a car trying to start & then does nothing. I live in a VERY remote area (80 miles from nearest Wal-Mart or McDonalds) so I know I will not be able to find someone to repair this for me. I have great doubt that I will be able to do it myself & my husband is an accountant so he is unavailable for another 6 weeks!!!!! Any suggestion
Whit the vacume plugged in and turned on start where the cord goes in to it and hold the cord whith each hand and bend it slightly. Move up the cord and do the same if there is a brake in the cord the machine will loose power until you bend the secti ... Miele Red Star Bagged Canister Vacuum
I wish to find a repair shop for hoover vacuums in the pickerington area can u help me?
Hi,\015\012You can go to this shop:-\015\012PICKERINGTON SWEEPER REPAIR511 W Columbus StPickerington,OH 4314714.1MI from Columbus (614) 837-6648 \015\012\015\012Thanks!\015\0 ... Vacuums
Vacuum nilfisk gsd repair insrtuctions - Nilfisk VT60 Wet/Dry Vacuum
... Nilfisk VT60 Wet/Dry Vacuum
Re: find a repair for vacuum
If you know someone that "can fix anything" there is a troubleshooting guide and parts available. Just click this link to view the guide...\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum
Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall
That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums
The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.
... Panasonic MC-V7515 Bagged Upright Vacuum
Repair Service I have a Miele White Pearl. I have a short in the head part of the vacuum ad need repair. Do you know a repair shop near Ely, Minnesota?
Maybe this link will help\015\012http://www.miele.com/locator.asp?nav=7 ... Miele Red Star Bagged Canister Vacuum
My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t
... Hoover Vacuums
Service manual for nilfisk gsd - Nilfisk GM 80 Bagged Canister Vacuum
Service manual will be difficult to find , because only for tech service. However go to www pdfservicemanual.com or www.retrevo.comGod bless you ... Nilfisk GM 80 Bagged Canister Vacuum
I need to replace the brushbaron my DC17 Animal model Dyson. It's almost four years old. I can't find the correct part number on the Dyson Website and I can't seem to find a Dyson repair center in Albuquerque, NM. What are my alternatives? If I can't service this machine without returning it to Dyson, I won't ever buy another one.
Hi,\015\012\015\012The original Dyson part number for the brush bar (often called brush roll) is: 911961-01\015\012\015\012If you type the above part number into Google Products (click link below) you will get a list of suppli ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My Morphy Richards vacuum cleaner (2 years old) will not pick up properly and also cuts out about vacuuming one carpet but then starts again later. Will I need to call our repair service?
Here are a few tips to try before you call a repair service.\015\012\015\012Most people think that putting their vacuum on the lowest setting picks up the most dirt. If you have medium to shag carpet, putting it on the lowest setting wil ... Vacuums
Either of my bissell porheat turbo 2x or my bissell pro heat don't have suction i would like to try and trouble shoot if i could due to the fact i am having difficulty finding a small machine repair center in my area could you possible help me or send a link which could help me find solution these machines are not more then a year and a half old if that thanks for your time and help warmest regards rebekah majors
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
The Vacuum canister is working but the tip did not havesuction power. Should I change it? Where can I finf the repair shp in my vicinity. My area is Ravenna, Ohio 44266. My Vacuum cleaner is about 10 years old similar to Ultralux 2000.
Try checking for blockages first, turn the foot of the vaccuum over and check the inlet tube, there may be a little flap that needs to be pulled forward for you to see if there is a blockage. ... Electrolux Vacuums
I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.
I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?
There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum
I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt
You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum
Nilfisk GD930 vacuum-can't find replacement brush
Hello mddamus,\015\012Try this link to a Nilfisk supplier, speak with a rep and they should be able to identify exactly what you need and provide that part for you.. ... Nilfisk GD 930 Canister Vacuum
Riccar 8850 Vacuum - Need parts diagram or SERVICE manual
I have a dirt devil featherlite bagless vacuum; model #088600. It has suction through the hose but not through the floor mode. I think there is a blockage in the hose area but cannot seem to take it apart enough to find it.
There are 3 screws 2 on the left side behind the hose and 1 on the right back by the wheel.that will take the cover off.if you need to get into the bottom there is a screw on the bottom plate in the area where it looks like the belt travels.is the br ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
The beater bar on my Dyson DC14 All Floors Bagles vacuum cleaner doesn't turn. There is no hair or thread caught up in it. All air-flow areas have been checked and there are no blockages that we could find. Any suggestions?
If it is not on the bare floor setting then you most likely have a belt issue it is not an easy fix I am sorry to say if your mechanically inclined I can tell you how to replace it. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n
From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums
Can I download a service manual for the Kenmore model 116.21600101C Vacuum Cleaner? Does any one know of a web site where I can find this?
... Kenmore 25512/ 25513 Progressive Canister Vacuum
My kirby is making a very loud noise and somehow the white fan inside has broken. I have the pieces. What do I need to do? I can't find a vacuum repair place near my location. Can I fix this myself?
What you need to do is a long process of taking apart the vacuum apart. Your fan broke so you are going to need a new one. So go to Kirbys website and look up a nearby vacuum store. Or More recommended a Kirby. It is a long process of taking the vacu ... Kirby Ultimate G Bagged Upright Vacuum