Having problems with your Numatic Henry Bagged Canister Vacuum ?

Stopped working hello im in france, so my henry has a two pin plug. i feel all that needs changing is a fuse, but i carnt find it. i have taken out every possible screw searching for it but to no luck. iv checked and cleaned wireing and checked cable for nicks. im now begining to think maybe the motor has gone?

Answers :

Hi!  Sorry you've had to wait so long for a reply, but I've only just stumbled upon your problem.  You probably don't need help any longer, but here goes anyway!\015\012You will not find a fuse, because there isn't one.  If your Henry just stopped, without making any strange noises or smells, it's very unlikely that you have a motor problem.  Quite often the wires can become broken inside the electric cable - with no visible external damage - especially where it enters the plug and can be subject to both bending and pulling stresses.  If the machine came to me for attention, that's where I'd look first.  Check the wires for electrical continuity.\015\012If you still need help, and this solution doesn't work, please write again and I'll suggest some less likely things to look for.\015\012Good luck!
Repair Help & Product Troubleshooting for Numatic Henry Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Stopped working hello im in france, so my henry has a two pin plug. i feel all that needs changing is a fuse, but i carnt find it. i have taken out every possible screw searching for it but to no luck. iv checked and cleaned wireing and checked cable for nicks. im now begining to think maybe the motor has gone?

Hi!  Sorry you've had to wait so long for a reply, but I've only just stumbled upon your problem.  You probably don't need help any longer, but here goes anyway!\015\012You will not find a fuse, because there isn't one.  If your Henry ... Numatic Henry Bagged Canister Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??

... Eureka Capture Upright Vacuum Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a

You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

I have a new scoba (irobot) the battery is charged the tanks were fillied and every time i hit the power button and then clean the machines "check the tank" light came on. i have done all the proper instruction checks an i have done all the trouble shooting section. the machine will only work (and that is for 5 minutes drying its head) when i hit power and the clean button twice. so obviously the machine is somewhat working

We had to prime the sensor. irobot suggested a turkey baster, but we didn't have oneso we used an empty visine bottle with the end snipped off and rinsed completely. this worked after the first try. thank you for your interest ... iRobot 5800 Scooba Vacuum

Numatic Henry Hound Turbo Head stopped working. Checked wires and contacts and cleaned. lOOKED AT THE MOTOR IN THE HEAD BUT DONT know how to check it is working

... Henry Numatic "" Canister Vacuum


... Electrolux UltraLux 2000 Bagged Canister Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.

Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Good morning. My elderly parents bought a Kichler ceiling fan for their living room 2-3 years ago - it has a remote and a globe design with a vive. The globe does not have any visible external nut to loosen to release the globe to clean it - the globe is screwed into the vine design which is attached to teh fan. I do not know how to easily remove the globe to clean it - do I have to ds=ismantle teh fan. I checked Kichler's site for over an hour - this may be discontinued.

The globe should be screwed in place by about a quarter turn ... Vacuums

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?

... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t

Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC04 upright vacuum Brush disengages (ratchet noise etc) when using on clean shortpile carpet. I have checked that brush is clean/clear but it disengages as if jammed every couple of minutes.

I hate to tell you this but that sounds like the clutch is bad ( a common problem ), It is not very easy to replace but you can buy it at sears ( part number ... Vacuums

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!

... Miele S7210 Bagged Upright Vacuum

When I try to turn on my DC14 vacuum, it won't stay started. I have to hold down the power button while I vacuum. I have checked for clogs and cleaned the filters, still no luck. Any suggestions?

It just needs a new switch under the "on" button...take it in for service it's worth it! ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I have a Dyson DC07 Yellow Vac, I use this vacuum professionally and clean it after every job so there is no issues with the filter which are replaced regularly. When you turn it on it makes a noise as if it were blocked....I have checked all pipes, hoses and now disassembled the machine to the point where the motor is out. I have found that a small rubber valve or bleed valve (Attached to the right hand detachable filter housing and activated via an internal spring) is popping when the vac

Hi, Where exactly is this spring? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

After carefully following instructions as to connecting stair cleaning attachment on Hoover SteamVac F5914-950 there is no flow of solution through the solution tube. We have thoroughly checked all connections but still no luck. What now????

... Vacuums

My vacuum sounds like it is screaming the entire time it is on. We have cleaned out every possible area, but it is still extremely load. Any suggestions?

Is it cleaning as good as it used to? 1) If not there may be an air leak. A crack or a hole will allow air to rush in. The motor will make a louder noise when not under load. 2) Have you changed house locations, ie Country? Diffferent house vol ... Bissell 87B4 Bagless Upright Cyclonic Vacuum

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t

... Vacuums

I am trying to change an old fashioned fuse, (house lights), luckily had a spare one. Have put the 15amp fuse wire through the whole thing, and trying to describe if I've got it right is alitle awkward, this is what i've done, cut a piece of 15amp wire a little longer than the old one, then loking at it, taken it straight through and round to left as I'm looking at it, and put the screw in, and obviously done the same for other side. My problem is that I don't remember taking the screws out of w

Hi.your descriptions are understandable and sound about right.as long as the wire is securely fixed to both pins, you should be ok.if there are any problems, especially if the fuse blows again fairly soon, then i strongly reco ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?

Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan

Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr

Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0799 seconds