Having problems with your Numatic Henry Bagged Canister Vacuum ?

Henry Hoover throwing trip switch in house

\015 The on/off button stopped working on the hoover the other day, I had to keep switching it off at the mains to turn it off. Then yesterday it threw the trip switch in the house. Iwhat has happened to it - I'm guessing that the motor has gone in it and will need replaced - if so, any idea of a price and the cheapest place to get one?Thanks\015

Answers :

Sounds more likely to be the switch than the motor, especially if it is the model with the top switch rather than the side "rocker" switch. If you are in the UK, speak to the technical people at www.a1cleaningsupplies.co.uk they can post a replacement. Otherwise outside or even within the UK you can contact the manufacturers technical people. Website is www.numatic.com
Repair Help & Product Troubleshooting for Numatic Henry Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Henry Hoover throwing trip switch in house

Sounds more likely to be the switch than the motor, especially if it is the model with the top switch rather than the side "rocker" switch. If you are in the UK, speak to the technical people at ... Numatic Henry Bagged Canister Vacuum

My Sebo hoover trips the house mains sockets every time I switch it on, yet doesn't trip the kitchen mains. Have replaced filters/bag to reduce load but still no good. What should I be investigating in the hoover? Thanks

Hello,It sounds like your vacuum is fine if it works when plugged in the kitchen outlet. It is tripping the breaker switch in the other room because the circuit is overloaded (too many things plugged in this circuit). Try unplugging some things ... Sebo Air Belt C2.1 Bagged Canister Vacuum

When i switch my henry hoover on it works fine for exactly 50 seconds then switches of for approx same time then comes alive again for 50 secs and so on...driving me nuts.

... Vacuums

Hoover power drive u6311 - How do u change switch? Does anyone have any idea how to remove the on and off switch, when I tap on the housing the motot and light goes on and off. Also does somebody have a exploded view of this model. also does anyone know the part number of the switch.

The swrtch is located in the bottom section of the motor. When the swtcih goes out it time to repalce the unit. The swtich is part of the motor. The switch rod run all the way down the body to the swtich located in the motor. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Henry hoover wont switch on

... Vacuums

Henry hoover won't switch on

... Henry Numatic "" Canister Vacuum

No power going to hoover have hoover turbo power 3. Plug is sealed but have changed fuse. Have had builders in house using it to renovate bathroom. Do you think it is now passed its sell by date was working until they got it. It dosent even switch on. Am ready to do them an injury as my upstairs is a mess

A Neighbour fixed it ... Hoover Vacuums

Bypass switch on a henry hoover

... Numatic Henry Bagged Canister Vacuum

My henry hoover will not switch on - Vacuums

If you have an elcrical tester you can verify that your source of electricity is in fact working.next test that the power is getting to the switch.check that the switch is working properly.If you have power all the way to the motor but it sti ... Vacuums

Henry Hoover hvr200/20 wiring to red switch 4 pin

... Numatic HHR-200 Henry Hound Bagged Canister Vacuum

Rewireing a new switch diagram on henry - Hoover Vacuums

This video may help you ... Hoover Vacuums

Henry hoover id tripping fuse box when i plug it in???

... Hoover Vacuums

On off switch broken on my Henry numatic Hoover

... Vacuums

My henry hoover is stuck in the hi suction function, I have changed the hi-lo rocker switch with a new one, but it still will not alter the power of the suction. Any other suggestions what I can check?

HI I have the same problem, and actually did the same thing to fix it..any ideas yet? please [email protected] ... Henry Numatic "" Canister Vacuum

My Old Henry hoover is making a VERY loud noise when switched on! Its still works but very loud, please help!

Most likely the motor bearings have worn out. You can fit a new motor quite easily, but if you need to pay someone else to do it for you the labour plus motor cost will probably make the job uneconomical. Sorry to be the bearer of bad news... ... Numatic Henry Bagged Canister Vacuum

The roller brush on my Hoover Z700 vacuum no longer runs when you tilt the handle back. I have tested every part that I can: the motor is good; the "magnetic switch" at the pivot point is good; etc. I'm now stumped. Any help or suggestions would be greatly appreciated as I don't want to throw away a $400 vacuum.

Has this not got a rubber belt drive? ... Vacuums

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering

Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

Does the motor overheat switch need to be replaced if it has tripped and reset on Hoover model u3940

Most of the Hoover overheat control switches reset when you UNPLUG the cleaner, and let is cool down for twenty minutes with the cord unplugged. ... Vacuums

Hoover windtunnel vacuum overheat switched is set off too frequently and I cannot finish vacuuming the house in one session. Lemon?

Please remember this part is doing a service to you. its basically saying my motor is getting so hot picking up this dirt that i better make him rest before he burns up. in most cases you will find that you either have a clog or your filters need to ... Hoover Vacuums

Henry hoover cuts out

A 5amp fuse will struggle on start up on anything over 1000watts. Check the rating plate on the appliance for total load ... Numatic Henry Bagged Canister Vacuum

Hetty hoover not working. It was working ok until I opened it up to search the bag for a missing jigsaw piece and I put it all back and I hoovered the mess on the floor, then switched off and switched on and hoover would not work? Is there a cut off button on Hetty hoovers?

Know cut off switch, its just not getting power ? 2 things its ether at the wall plug or in side the unit. I have never found a fuse in side them , so it may be just a lose wire did you try other plugs in the house . good luck DFD ... Henry Numatic "" Canister Vacuum

Change belt on hoover whole house - Hoover Whole House Bagless Upright Vacuum, UH71214

... Hoover Whole House Bagless Upright Vacuum, UH71214

Hoover RepairGood Day. I have a hoover HWD 020. It seems that the on/off switch broke, but I don't know how to open the space ship looking lid to get to the switch. Any idea?

... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Hoover Windtunnel On/Off switch will not turn Off...Switch seems to work O.K. when pressed directly but not with handle switch...It will turn on but not off..Cam seems to be intact on switch actuator..How does switch come out? Thanx

Take the handle off, then remove the tool holder, then you can get to the switch. Just has tabs on each side of switch, depress them and push it out. These switches will do this after awhile, replacing them is usually the way to correct the problem ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0536 seconds