Having problems with your Numatic Henry Bagged Canister Vacuum ?

Henry's switch has come out.I found the red switch and 2 bent bits of metal. How do they fit together to make him work again?


Answers :

Rather than coming out, it sounds more like the switch has come apart. It also sounds like you haven't got all the bits. Even if you'd got everything, and knew how to assemble it, there's a good chance it will come apart again anyway. The only safe thing to do is get a complete new switch.\015\012
\015\012I value your feedback, so please remember to rate this response. Good luck!
Repair Help & Product Troubleshooting for Numatic Henry Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Henry's switch has come out.I found the red switch and 2 bent bits of metal. How do they fit together to make him work again?


Rather than coming out, it sounds more like the switch has come apart. It also sounds like you haven't got all the bits. Even if you'd got everything, and knew how to assemble it, there's a good chance it will come apart again anyway. The only safe t ... Numatic Henry Bagged Canister Vacuum

I replaced a Intermatic light timer with a GE 15086 timer. I have read several solution, but none fit my wire sceme. This is hooked up as a 3-way switch so the second switch can turn outside lights on manually. Here is what I have; Four timer wires: R B W G Wall outlet: B, B & R (Two), G, W bundle What ties in together to make it all work?


1) GE 15086 is not a 3-way timer.GE programmable timers are for single-pole switch replacement only. I have tested this timer, and own several GE timers, and many other brands.2) Open following link to identify timers that work for ... Vacuums

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

The On Off Switch has stopped working - loose in the fitting - If you jiggle a bit some times starts!


No other way but to open to access the switch and first of all use a good switch cleaner to try if the contacts gets clean . check the continuity and repeat. Refitted it tight so that when you switch the lever moves to contact.If not there is no way ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

There were no instructions included with purchase. I have viewed the assembly video but have nothing else to go by. I believe I have not put it together properly now as it makes a whale sound with each rotation and now the reset switch is pushed in and not working.


What sort of a Vacuum is it? and where is the 'Whale' sound coming from?With each rotation?-- of what-- the power nozzle-- or the vacuum-- or what?Please tell us more, so we can understand what is wrong-- and with what? ... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My Dyson DC25 animal is having issues. I believe everything is working correctly except I have realized that the mechanism which switches the hose/valve between the wand and the vacuum head isn't working properly. The two gear pieces that move the hose placement aren't close enough together, so they don't work together. It looks like there is a washer that I could potentially remove on the clear gear piece which would allow it to sit closer to the assembly. Would that work? Currently I am


... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity


... Vacuums

Henry brushes seem to catch in the carpet when pulling-will the brushes soften and make it easier to use as it makes the head bounce of the floor a bit when pulling making it harder work to vacuum?


There is a "see-saw" type switch on top of the cleaning head (the part that you push across the floor). This raises and lowers the brushes according to the type of floor you are vacuuming. Move this switch to the other postion and you will find that ... Henry Vacuums

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?


... Vacuums

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Miele Cat and Dog has stopped working. There was a slight burning smell and then it switched off completely. Also, the bag was a bit wet, so have replaced with a fresh one but still not working. Help!


... Miele Cat & Dog 326i Bagged Canister Vacuum

The CV750 stopped working. It will come on sometimes but most of time it will not work. I installed new bag and cleaned filter. Green light on side of unit is on. Switch on side of unit will not make it come on either.


My CV750 comes on but makes a very loud noise. it sounds like something is stuck then it lets loose but the noise sounds terrible and the unit smells warm. I installed a new bag and cleaned filter. Green light on side of unit is on. Switch on side ... Broan-NuTone CV750 Central Vacuum

The switch on and off wont work so i took it off and it works but know iam having problems putting it back together the spring are the problem


Those springs are tricky to get back in. you can use the flat end of a screwdriver to hold them down and compress them. I would recomend taking it to a proffesional to get it put back together right before you break the plastic and cost yourself some ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?


I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Switch Problem The red switch to put on wont stay on the motor runs but as soon as you release your finger from it the motor cuts out. what do I need to do to make it work as it should?


It sound like the switch is loose if you are able take the handle apart and plug the leads back into the switch. be sure to unplugit ffirst ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank


You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

My Animal Dyson (the purple one) is making strange noises. The ball will not roll. I've taken it apart and put back together and it works for a couple minutes and then it won't work again I think it's Model DC24 or 25. Pretty sure its 24.


... Dyson Ball DC24 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0599 seconds