Having problems with your Numatic Henry Bagged Canister Vacuum ?

My Henry keeps shorting out? Changed fuse and bag but still wont work?


Answers :

Most common cause of this problem is a damaged flex. Damage may not be visible externally, but after a lot of bending and pulling the wire inside the flex can break. This usually happens close to the plug, so examine it very carefully for signs of damage (if there has actually been a short circuit, there may be a tiny hole blown in the outer insulation). Unfortunately there is no easy way to locate an internal break without special testing equipment. You can try just cutting off the old plug with about 6 inches of flex, and then fitting a new plug - if that doesn't work you may need professional help. Good luck!
Repair Help & Product Troubleshooting for Numatic Henry Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Henry keeps shorting out? Changed fuse and bag but still wont work?


Most common cause of this problem is a damaged flex. Damage may not be visible externally, but after a lot of bending and pulling the wire inside the flex can break. This usually happens close to the plug, so examine it very carefully for signs of da ... Numatic Henry Bagged Canister Vacuum

Cleaner stopped working, changed bag still not working. Have checked mains fuse and liittle fuse on printed circuit board. When cleaner is on moving slider to the off positon the LED's glow red for a fraction of a second. Reset button does not feel as though it clicks when pressed, it does not seem to move. Many thanks, Hugh


... Panasonic MC-E583 Bagged Upright Vacuum

Henry hoover my hoover has stopped working i have changed the bag and fuse and it still is not working i dont know what to do


... Numatics Numatic Hetty 200a Hetty Hepa Canister Vacuum Cleaner with Autosafe

My henry stopped working, changed fuse and bag - still not working


... Numatic Henry Bagged Canister Vacuum

My henry just wont work? fuse changed and still not any life? what else could it be ? Thankyou /


Could be one the following\015\012faulty mains lead,\015\012mains lead contacts on the cleaner,\015\012on/off switch,\015\012capictor,\015\012wire off motor ... Vacuums

My dc 05 isnt working and i cant understand why , i have cleaned all filters etc and i also changed the fuse on the plug , which after i didi that it attempted to start but then jus cut out again so i thought the fuse had blown again , so i checked the fuse but its working fine could there still be a blockage somewhere in it or is it something electrical which means my dyson has to go to the dump :(


Most common cause of this problem is a wire broken inside the flex, usually either just where it leaves the plug (easy to fix) or at the other end (more of a problem). In either case, this is no reason to dump the machine - it can be fixed at a fract ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Won't work My Eureka Mighty Mite 3670 Bagged, was working fine, and we unplugged it to switch to another outlet in another room and it just stopped. We tried several other outlets and it just won't turn on. We thought maybe it got hot because we had been using it for a while and we let it rest for a while and then changed the bag just to be sure, although it was not full. But it still will not turn on. Any ideas?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=12151&thid=646957\015\012Won't work (by 2 users)\015\012Posted by AndiR on Jun 04, 2008\015\012My Eureka Mighty M ... Eureka Mighty Mite 3670 Bagged Canister Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

Bag full indication comes on; changed bag; still wont run.


Turn the knob on the top of the vacuum all the way to the right and try it again ... Electrolux UltraLux 2000 Bagged Canister Vacuum

The vacuum leaks dust around the joint between the bag and the vacuum. I unlatched the bag, removed and emptied it, and replaced it. However, the vacuum still leaks dust around the joint and the bag keeps working loose. How can I make sure that the bag is securely latched so that it does not leak or come loose? I have no manual. Thanks.


... Bissell 3065 Power Partner Vacuum

Electrolux oxy 3 vaccum has stppoed working and all three blue lights flashing My electrolux oxy 3 ZO6330 stopped working suddenly and all lights are flashing. I've changed the bag and filter and its still not working. Any ideas??


... Electrolux Vacuums

Was using my Miele Champagne vacuum, powered down, changed the bag, and now I have no power. I checked to make sure all lids were securely closed, still no power. Checked to make sure outlet was working, still no power...help.


Most likely the cord went bad, one side of it opened up, you will have to replace the cord reel asm. if this is the problem, Could also be a switch, electronic control or the motor. ... Miele Vacuums

Using hoover, stopped working. Bag very full so changed. Hoover seems very hot. Will not work. Checked fuse


Give the vacuum time to coold\\ down, then try again. If it still doesn't work, take it to a repair shop to be checked.\015\012When a vacuum is used for long after the bag is full, the motor can overheat to the extent that the motor burns out. ... Miele Cat & Dog 326i Bagged Canister Vacuum

My hoover keeps cutting out I have washed the filters and changed the bag but still keeps cutting out every 15secs


... Hoover Vacuums

Turned Hoover on and worked as normal for 10 mins then for a split second went off and then on again a coupe of seconds later went off completely. Tries different socket and changed the fuse. Still not working.


Internal short most likely to a feed wire to the motor ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

We have an MC-3003 vacuum cleaner which keeps cutting out. We've changed the bag, but the problem still occurs with a new bag fitted. Could it be an electrical fault and is the machine repairable?


... Panasonic Vacuums

It will not turn on the bag was full. we emptied the bag . it still does not work. The fuse is Ok,


If this just happened, tho I see by your posting it was over an hour ago... sometimes the thermal reset there has tripped off and needs for it to cool down. The other thing is there is a reset button on the unit itself that should be pushed in for i ... Broan-NuTone CV450 Central Bagged Central System Vacuum

It just keeps saying that my bag is full and cutting out, bag not full and have tried changing it anyway, but still cutting out


I would check the air filter. It sounds like it's over heating and shutting off because it doesn't have good airflow.Jim ... Sebo X4 Bagged Upright Vacuum

My nilfisk action plus keeps stopping. it used to re-start if I drew in the lead and/or left it for a while but now it won't start at all. i have changed the fuse on the plug (not the thermal fuse), but that has not worked. can you advise?


... Vacuums

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.


It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Vax infinity 1900 suddenly stopped working now no power gets to it, i've changed fuse still no power.


I have an infinity nv29 that stopped working while I was vacuuming. According to the manual I was supposed to unplug it for about 45 minutes and then try it again. I waited for over an hour and tried it again and it still won't turn on. Any suggesti ... Euro-Pro NV31 Infinity Vacuum

My jm3 1500w super lightweight cleaner simply just cut out last night, only had it a couple of months, changed fuse and still not working, filter was already cleaned out,pipesare not blocked either.HELP


... Vacuums

Kenmore cleanscape stopped working...changed the filter and pushed reset but still wont turn on


... Kenmore 34721 Upright Vacuum

Light burned out and at same time sucking motor stopped working. Brushs still turns. is there as fuse I can change out or is the motor toast ? this unit is less then a year old


Contact your local warranty center they have had problems with that model ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1116 seconds