Having problems with your Oreck Ironman Vacuum ?

My ironman turned off and then the suction was not as good.

Answers :

Repair Help & Product Troubleshooting for Oreck Ironman Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My ironman turned off and then the suction was not as good.

... Oreck Ironman Vacuum

Dyson DC14 is not picking up as it should and the hose hardly has any suction. I have checked for blockages and there are none. When i turn it on it sounds like there is good suction then there is a second noise like the suction is escaping somewhere.

Check this video out ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s

I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

Bissell cleanview - brush not turning. can i fix it...vac is 3 mos old? brush turns freely by hand. suction is good thru hose.

Put a new belt on it ... Vacuums

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?

... Bissell Vacuums

The motor works, suction is good, but the roller brush will not keep turning. It turns at start up, then stops a minute later.

... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

The brushes wont turn,but it has good suction for the hose

If the belt seems to ok, you may need to order a replacement clutch assembly. These are not that expensive and can be ordered through dyson or possibly online. Switching from bare floor to carpet while the motor is running is really stressful on th ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

7600 model - motor runs and good suction present Does not self propel and brush does not rotate although I can turn it easily

Your brush drive belt has broken. Generally you need to remove the bottom of the machine in order to get to it. On the belt you should see numbers even if you don't, just look on the bag that the new one comes in for the brand and model you have. Bel ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Sebo upright barged hoover- good suction using hose, brush wont turn, sounds fine when running, nasty wineing noise when stopping?? help!! i love my hoover, have checked for bolckages....

The real clue seems to be the brush is not turning, a bad belt is possible or a blockage at that head, if you cannot get the brush moving the rest does not matter. ... Sebo Felix Classic Bagged Upright Vacuum

I do not have any suction, to the base or the wand. My brushes also do not turn. The belt appears to be attached & in good condition and there are no clogs (that I can find)

Some times there is a pan beneath the vacume and an opening there, it may be clogged there, thats not real unusual, hope this fixed it,, ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum


... Hoover Vacuums

Hoover canister vacuum (windtunnel)- turned it on and it had good suction, then smoke came out and it smells like something is burning. Is it the motor burning up or something else?

Probably the belt..\015\012Turn it over so the bottom is facing up..\015\012Remove the plate that surounds the brush..\015\012Check to se if brush is spinning frely and that the belt is on there poroper ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The drum is not turning when I the vacuum is on. I have good suction. What should I do?

By drum I take it you mean the beater bar on the bottom? I would check the belt and probably replace it. remove the screws holding the very bottom of the vacuum on and remove the access plate / cover. you should see the belt or whats left of it. ... Kenmore 35912 / 35913 Progressive Upright Vacuum

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode

... Hoover Vacuums

Makes a high pitched noise when turned on and suction is not as good as when new. How do you break it down to check the motor? I suspect that is where the noise is coming from.

... Vacuums

'eureka whirlwind lite' vacuum - brushes turn but no real suction

... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?

So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction When I turn the vac on it sounds ok but there is no suction and the brushes don't turn. Alot of air does come out of the two exhaust vents and the brushes will turn manually.

Hey, how are you ?\015\012\015\012here are a ew things that could be causing you sorrow\015\012\015\0121.) Check your vacume to ensure that it isnt clogged anywhere\015\012\015\0122.) before your compressor and aft ... Hoover F6020-900 SteamVac Upright Vacuum

Brush assembly will no longer spin on carpet however the suction from the system is still good. Unit is only 5 years old.

Probably a seized beater roller (the bearings wear out). Just order the new part and replace it and you'll be one your way again. And of course maybe a belt. ... Electrolux Centralux Vacuum

No suction but good exhaust flow

This sounds like you have a loose pipe connection somewhere in your system. Physically check all connections. If you can't find anything suspicious, call a vac repair man that specialies in central vac repair. Joe ... Electrolux Centralux Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.

Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I had to empty the canister and when I put it back on and turned on the vacuum, the suction does not turn on. The brushes are rolling and the attachment suction works fine. Any suggestions?

... Eureka 431A Optima Bagless Upright Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0508 seconds