Having problems with your Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum ?

Hi, I can't remove the filter...can you tell me how? Thanks


Answers :

Repair Help & Product Troubleshooting for Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed


... VAX Appliances Vax X3 Bagless Upright Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Carpet Removal I need someone to tell me what is the best way to take up or remove carpet.


Cut it into two foot strips with a utility knife for easy carryout, then if you need to remove the tack strip as well use a pry-bar but be careful as the tack strips are very sharp ... Vacuums

I need to know how to remove the dirt container on the eureka bagless vacuum. It says that it is easy to remove, yet we cant figure it out. is there some trick to it that we dont know?


There is a lever at the bottom of the dirt cup,turn it to the left and pull out the dirt cup.note while you have the dirt cup out make sure you clean all the filters there is one right above the dirt cup pull out on the right side and there is a filt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),


Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

I cant figure out how to remove the housing cover


Hello,\015\012\015\012Here's an excellent video showing you how to replace the clutch on a Dyson vacuum cleaner. It's a moderately difficult repair, but this video really helped me the first time I had to do this repair. I hope this he ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Let's try this again. The main vacuum and hose works fine, the "foot" does not. When I turn it on, it shuts off automatically and the light comes on telling me to "check brushroll". I did this and removed all hair, strings, etc., Still won't work. Please respond. The last post took over 30 minutes with no response.


Sounds like you have hair or carpet buildup in the roller and it is not freely rotating and you are getting an error. If there is no buildup, then roller bearings may be frozen up, or the unit has a faulty capacitor and is not going to work due to el ... Vacuums

I cant remove my wand on my Dyson vacuum. - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson. It is possible that if the hose is blocked that the wand handle may become jammed. For help releasing this, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US) and one of our advisors can talk yo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Have Fresh Aire 2.1 about 4 years was running great then went dead. I cant find where the fuse is and have unit apart. I plug in no fan dim display shows to errors. Unit was pretty dirty at the time. I need schematic and suggestions. Also need to knpw how to remove the honeycomb from the light unit to check for blown bulb. Seems brittle and I could break it with trying to pry with augur or sharp screwdiver object.


I'm sorry this may only be a partial help. But fuses are usually very close to the motor, OR where the switch is located. Pretty easy to find by testing but you have to be or so careful you dont electricute yourself. Now if your testing shows v ... Vacuums

My vacuum cleaner works, all but the "foot". It turns off automatically and the light comes on telling me to "check brushroll". I've done this and removed all hair, strings, etc. It still turns off automatically, while the main vacuum and hose remain on. What else can I do?


Please post back with a brand and advise more info, however , I assume this is a canister vac with hose and `power head``. Often a power head brush roll will build up hair and thread which travels and winds up at the end of the brush wher ... Vacuums

I cant remove the houseing off the bottom of the motor can someone plz help


Start by taking the bottom off and remove the brush roller and belt.go back to the top and on each side of the upright where it meets the base you will see 2 plastic covers that are held in by screws take those out and that will disinguage the uprigh ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Cant remove belt no room at end of motor shaft, looks defective


You have to remove the cover. It isn't a defect, it's a way to keep unqualified people from messing with the product. ... Eureka Smartvac 4870 Bagged Upright Vacuum

HOW DO YOU CHANGE BELT CANT SEEM TO REMOVE BOTTOM TO GET TO IT KENMORE WISPERTONE 116


The top cover to the light lense pops off at the ends. When you get that cover off then you will see 2 screws that are by the swivel neck. Take those out and then the whole body top cover comes off. That will get you into the roller brush and belt ... Kenmore 23313 Whispertone Bagged Canister Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

The lights which tell you if you are going at the right speed on my Bissell PROHeat Pro-Tech have stopped working. Just wondering if this could be as simple as a bulb or more serious. Also, how do you remove the clear panel at the front for cleaning? Thanks


The clear view window is unscrewed with a philips screw driver on either side of the nosel opening (top) but make certain the handle is layed back so as to alleviate twisting off the clear view cover. There are six (6) screws that hold the top cove ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I cant get my kirby to blow out...bag is removed from seating...its plugged in...i attach the hose to the place where the bag goes, but it wont run


I did get it to work! It was a struggle, but It finally hit that hidden switch just right. The hose attaches to where the bag goes, and it just wouldnt seat properly. I suppose there might be some wear there on the hose end that twists in . ... Kirby Vacuums

Hi, I can't remove the filter...can you tell me how? Thanks


... Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum

Unblocking sinks Can someone please tell me how to set up my kirby hoover to unblock my bathroom sink the sales man did show me a few years ago but i have lost my manual and cant remember??? Many Thanks Nina


Remove the brushead and attach the adapter (round cup-looking device with a screen or grille on the front).Attach the hose to the blower (bag) side of the machine.In your attachment caddy,there should be a round rubber attachment with rubber teeth ar ... Kirby Ultimate G Bagged Upright Vacuum

S catch i have taken the top part of handle off, removed the screws under hose wrap, and layed the bottom part of handle down, i cannot find the s catch, can you tell me exactly where it is and what it looks like. i have looked all over this thing. thanks randy the model # is 8905


\015\012\015\012Just pull where I marked, it should come loose. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I am trying to remove the motor in my Kenmore canister vaccum but cant seem to figure out how to get it out.


Without the model number, I don't know which model you have. But you can go sears.com, click on the parts link, then put in you completer model number, choose the cannister or main unit, a parts list and a picture diagram will come up, you maybe abl ... Kenmore 22812 Bagged Canister Vacuum

Hoover Alyx Pets 2000w Hoover Model TC1208 001 Virtually no suction, have checked for blockages but cant seem to see any, however i can't remove the hose to check it. Any ideas?


Did you check the HEPA filter? I have the same problem with mine if I don't clean the filter after using it. It's a dirty job but helps for a while. ... Vacuums

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks


Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

I keep getting errors on my roomba 560 telling me that I need to remove and clean the brushes. I reset it and it goes for about 2 minutes and beeps again (and the brushes look fine) What am I missing?!


Try also cleaning all the filters ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0335 seconds