Having problems with your Oreck Vacuums ?
Oreck vacuum is smoking and the roller is not turning. vacuum is turning on and inflating well.
Remove the roller assembly and clean/oil (3-1 oil or similar) the end bearings which are usually jammed with string, thread, and hair. Check the belt for burning or other damage, assemble the belt over the roller and motor shaft, then install the roller into the base making sure to twist the belt if required. Look for a guide diagram cast into the base. Hope this helps!
Sounds like the roller is jammed up. The motor keeps driving the belt, but for some reason the belt cant drive the roller. The smoke is coming from the belt, Clean the junk out from the roller.
Repair Help & Product Troubleshooting for Oreck Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Oreck vacuum is smoking and the roller is not turning. vacuum is turning on and inflating well.
Remove the roller assembly and clean/oil (3-1 oil or similar) the end bearings which are usually jammed with string, thread, and hair. Check the belt for burning or other damage, assemble the belt over the roller and motor shaft, then install the rol ... Oreck Vacuums
My Oreck XL was working fine, then when I vacuumed a shag rug is started smoking and smelled like something is burning. (I changed the bag, checked for clogs--none found, and roller brush is turning. It has a metal handle.) Now I am afraid to use it.
Even though the brush is spinning, the belt is probably worn out and stretched. when you vacuum the shag carpet, it puts more drag on the brush. try running it on a shorter carpet or hard floor for a few minutes. if it doesn't smoke, then you know i ... Oreck XL2000 Bagged Upright Vacuum
I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap
... Oreck DutchTech DTX1300A Bagged Canister Vacuum
I have an Oreck canister vacuum, it says fc1000 on the bottom sticker, it's red. My problem is that the suction in it works perfectly, the belt is ok, and the roller can turn, but the motor doesnt turn it when I turn on the power.
I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!
The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug
... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?
Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.
Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum
Kemore Progressive Vacuum 116.35923500. Where is the switch that turns on the agitator roller. It will only turn on if the handle is laying flat. When I lift it up slightly the roller turns off. Bill
... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue
Halo vacuum The rollers on my Halo Vacuum will not turn. I turn on the switch below the on/off switch and nothing happens. The vacuum is working. Just no rotation
Roller does not turn; I was vacuuming a rug and a string got stuck in roller-took it off but now the roller will not turn. suction is fine.
The roller drive belt may be stripped, worn partway through where it goes around the motor shaft, thrown off the motor shaft, or broken. Take the bottom plate off the carpet sweeper and have a look.If the belt was damaged when the roller ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?
THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum
Dyson DC14 animal vacuum does not turn on however the roller brush does come on.The hose was clogged and that was cleared but vacuum still will not turn on.
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums
Eureka Smartvac 4870 Bagged Upright Vacuum Smokes when I turn it on
Check the air intake! Its probably clogged! ... Eureka Smartvac 4870 Bagged Upright Vacuum
Oreck vacuum keeps turning off - Oreck XL2200 Bagged Upright Vacuum
... Oreck XL2200 Bagged Upright Vacuum
My Dirt Devil Vibe bagless vacuum started giving off a burning smell. The brush roller was jammed with hair. I immediately shut it off and cut the hair out of the rollers with scissors until it turned freely. When I turned it back on, the smell was gone but there's no suction now. Did I ruin the belt or something else?
It's more likely there's a clog in the hose somewhere, possibly where it connects to the power nozzle. Detach hose and check the PN. \015\012If there's no clog in the PN, detach hose completely from machine and try to drop a marble or coin th ... Windsor SR12 Sensor Bagged Upright Vacuum
Vacuum won't pick up any dirt - there's no roller marks when vacuuming carpet. Roller does turn and filters are clean.
Hi,\015\012\015\012When you turn the roller, you should feel some resistance from the belt. Remove the base blate that surrounds the beater bar. Check the belt. Take care in removing the beater bar, so you can get it back in the same w ... Dyson DC14 Bagless Upright Cyclonic Vacuum
I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt
You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum
Oreck XL My Oreck just turned off in the middle of vacuuming and I smelled a burning smell. I am thinking that if I can take it apart and remove whatever turned it off, it will run again.
Your roller brush is probably bound with hair and is not able to move ... Oreck XL2600 Vacuum
The roller will not turn off on our Oreck Halo. As soon as I plug it in, the roller turns on. Any ideas?
Not familiar with the Oreck Halo, but that sounds like a shorted switch. ... Oreck Vacuums