Having problems with your Oreck Vacuums ?

Removing fan housing from oreck xl21 does not appear to be a nut holding the housing

\015 Can see washer but not nut holding fan housing but will not pull off\015

Answers :

Repair Help & Product Troubleshooting for Oreck Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Removing fan housing from oreck xl21 does not appear to be a nut holding the housing

... Oreck Vacuums

Oreck xl 9300 can not remove seal cup to change fan - appears glued?

You should be able to prise it of it will just be a push fit see link belowhttp://www.vacpartswarehouse.com/Oreck-XL9300-s/2925.htm ... Oreck Vacuums

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]

You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.

If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.

Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?

Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?

They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

Kirby Heritage II 2HD Vaccum Cleaner. I have removed the housing and reached the motor shaft for the vacuum fan. How do you remove the fan from the shaft.

Hi, you can visit this site to view how to remove the fan from the shaft...http://www.diyonline.com/servlet/GIB_BaseT/diylib_article.html?session.docid=1678Take care ... Vacuums

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak

... Kenmore Progressive 35922 Bagged Upright Vacuum

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.

... Vacuums

Good morning. My elderly parents bought a Kichler ceiling fan for their living room 2-3 years ago - it has a remote and a globe design with a vive. The globe does not have any visible external nut to loosen to release the globe to clean it - the globe is screwed into the vine design which is attached to teh fan. I do not know how to easily remove the globe to clean it - do I have to ds=ismantle teh fan. I checked Kichler's site for over an hour - this may be discontinued.

The globe should be screwed in place by about a quarter turn ... Vacuums

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.

The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?

Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!! ... Vacuums

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]

... Miele Vacuums

I have an Oreck xl21 that makes a lot of noise. I think the fan is loose of the shaft causing it to wobble. I cannot seem to get the fan off the shaft. Does anyone know how?

... Oreck Vacuums

How do i remove the canopy of my hampton bay ceiling fan? I want to relocate it and there are no screws or nuts visable on the outside. I've tried turning both ways and it gives a little but the whole fan moves when i turn it. I've tried pulling down even prying it from the ceiling. Nothing works. HELP!

HI!!\015\012\015\012I assume you've removed the blades. so next step is to check the canopy. The Ceiling Fan canopy has a decorative ring RIGHT against the ceiling that covers some screws. Remove the ring, remove the screws ... Vacuums

We have a Eureka 71B Hand-Held Vacuum and it looks like the belt broke. I removed the two screws at the bottom that should release the housing that holds the belt. However, the housing still does not come apart. Any advice? Thanks.

There's a 3rd screw hiding underneath a plastic shield. You'll have to drill or cut off the covering but then it's pretty easy to deal with. ... Vacuums

Dyson DC05 Is it possible to replace the cable in a DC05 cable rewind assembly? I do not appear to be able to remove the spring housing from the rest of the assembly the disk with the cable exit hole seems to be fixed is it removable?

Yes it clips out ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Oreck xl 21 fan housing has new design. willit stillfit my older vac

It should. You can call Oreck and talk with them and give them the serial number off your vacuum and they can look it up and tell you for sure if it will fit or not. ... Oreck Great XL21 XL 21 8 Pound Upright Vacuum Cleaner

How do you remove fan off motor oreck xl9800

... Oreck XL2200 Bagged Upright Vacuum

How do I properly remove the fan from an Oreck XL9200s upright vacuum? It looks all chewed and beat up.

You will need to grip the motor shaft with a vise grip or similar with a pad underneath so as not to score the shaft , which in tun would damage the belt. A piece of tire tube or leather will help. The fan is threaded and will rotate off oppos ... Vacuums

How do i remove the fan housing assembly from the handle connector on the 2600HH

There are two or three screws resest. ... Oreck XL Ultra Bagged Upright Vacuum

How to remove base plate - Oreck XL21 Bagged Upright Vacuum

Here is the manual with full instructionshttp://dem ... Oreck XL21 Bagged Upright Vacuum

How do you remove the handle to clean it? - Oreck XL21 Bagged Upright Vacuum

I am unsure why you would be removing the handle to clean it. It really is not necessary, but the handle grip is held together with 6 screws, take out the screws the two halves come off of the handle pipe.\012 \012 ... Oreck XL21 Bagged Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter

There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0560 seconds