Having problems with your Oreck Vacuums ?
Oreck xl 888 won't work
\015 Suddenly stopped working\015
Repair Help & Product Troubleshooting for Oreck Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My Brother XL4030 wont swtich from bobbin winding to sewing - bobbin winding works but when i switch to sewing just wont work
Pickup water wont pickup the water after putting it down very little comes up into the tank .it worked fine when we baught it but after not useing it for some time it worked now it wont **** water up at all can anybody help.
The clear shroud covering the front of "hood" has two sheet metal type screws at the bottom in front of the brushes, these two screws also hold the little straight brushes ( one on each side) in place. I found one of these screws had broken it's plas ... Hoover F6020-900 SteamVac Upright Vacuum
I have the smaller oreck portable hand vaccuum & it won't turn on. It was working fine in the one bathroom & I moved to the other & bathroom & it won't work or turn on at all?
Check the wall outlet has poser and make sure the plug is fully inserted. ... Oreck XL2200 Bagged Upright Vacuum
DC07 brush wont spin on bottom, took all apart and wont work
Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions
If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum
I HAVE A SET OF ANDIS AGC CLIPPERS WHICH I HAVE HAD FOR THE LAST 2 YEARS. WHEN I CAME TO CUT MY DOG THIS TIME THEY STOPPED WORKING & WILL ONLY WORK BRIEFLY IF I TIP THEM UPSIDE DOWN OR SHAKE THEM SLIGHTLY. IF I HOLD THEM THE CORRECT WAY UP THEY WONT WORK.
Inside the clipers there is a spring switch,,its broken? or all the vibration in the clipers has shook a wire off inside,,,in short its time for a new set of clipers,, ... Vacuums
I have a eureka altima bagless and it wont pick up dirt i clean it and everything it just wont work
The belt is probably worn, stretched or broken that is why it is not picking up. Here is\015\012a link to the owners manual which has instructions and a link to the\015\012belt you need. ... Eureka Capture Upright Vacuum Vacuum
My McCulloch whipper snipper was working just fine after finding cracked fuel lines,. Replaced wiht home made lines and worked fine until Sunday and now wont start at all . Checked everything , now think its electrical Would like to kow if there is anyone in Perth who can sort this out
Your local lawn mower repair shop will be able to fix it for you. ... Vacuums
Oreck xl commercial spits out dust on bare floor but work on carpet. It is about 15 years old. Bag has been changed. Brushes are spinning so belt is working. Started about 2 weeks ago. HELP!
It might be that the beater brush is spinning when you tip it up to look at it but slight pressure of it contacting the floor is enough to stop it.\015\012If it were my machine I would remove the beater brush and clean it as best I could, paying part ... Oreck XL Ultra Bagged Upright Vacuum
Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho
Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums
My bissell proheat carpet cleaner wont turn on. Its plugged in and everything but wont turn on. I've had it for a few years but its always worked before. Do they have to heat up if I haven't used it in a while?
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Re UH70040W seriesZF12.0.I can't seem to get the brushroll agitater to work it just stays off and the brushroll does'nt work the belt that drives it wont grip the roll? It's brand new!
I followed the instructions,you have to release the handle as though you were vacuuming and it works automaticly you can't put it on ON when it's upright!! Duh ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My suction wont work. It works for about 2 swipes and then quits. When you stop and restart it does the same. It is only 2 months old!!!!!
Hopefully you don't have a bad impeller on the suction motor. Start with this though: Make sure that you check for obstructions in ALL of the tubes, from the brushes all the way to the bag/canister. I've found that in many cases, especially if you ha ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My dyson works with the hose but wont work the normal way
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My bissell vacuum attachments wont work, as soon as i attach anything besides the crevice tool it wont ****,but sucks fine when its just the hose
Tern upside down remove plastic cuvier look wear the hose gos fillip skew driver ... Bissell 6594 PowerForce Bagless Upright Vacuum
Why doesnt my Dyson auto adjust on our carpet? We have a taller, soft carpet and it digs into it, making it very difficult to vacuum. We have had the vacuum for about a year at another house and it worked GREAT on the berber......our new has a tall carpet somewhat like shaved berber and now the vacuum wont work.
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Scuncii Steamer wont work wont blow steam anymore
It is probably clogged with rust or limescale - can happen with steam cleaners. Sadly there's no way around this but to try a limescale remover in distilled water such as Calgon limescale remover. Fill the kettle as normal and give it time to boil up ... Scunci 52067 Handheld Steam Vacuum
My shop vac stopped working while vacuuming i looked at everything i could look at and still wont work tried several other outlets checked cable still nothing
Staring from the failrue of the power cord,the main plug,t he main switch each of the sections must be tested for continutiy before we can conclude.\012SInce it is clear case of power failure the voltage must reach the motor,if not back trace t ... Shop Vac Vacuums
Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.
It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin
The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
Wont spray i have a bissell pro steam 2x and it wont spray the water out, i have cleaned everything and nothing seems to be working ...please help
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Tv well it wont go back to number 6 which is the output for the direct tv hd box.There are 7 total outputs and it only letting me get to 0,7 every thing in between it wont let me get to.
Did you try unplugging you box from the a/c power. If that doesn't work, then you should call Direct TV, they need to reset your box. ... Vacuums
Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks
If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum
The hand-held wand wont slide back into the tube. It wont go down far enough to click in and become the handle again. It was working fine but all of the sudden won't fit back in.
Sounds like the tube has something inside of it that is obstructing the path. veriffy the the "female" end of the tube isnt obstructed, and also, make sure that nothing is bent ( which can happen easily). use a flashlight to shine down into the tubes ... Dyson Ball DC24 Bagless Upright Vacuum
The switch on and off wont work so i took it off and it works but know iam having problems putting it back together the spring are the problem
Those springs are tricky to get back in. you can use the flat end of a screwdriver to hold them down and compress them. I would recomend taking it to a proffesional to get it put back together right before you break the plastic and cost yourself some ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum