Having problems with your Oreck Vacuums ?

Oreck xl upright vacuum

\015 Everything is fine, except the beater bar won't turn. There had been a pushpin stuck in it so it couldn't turn, but when I took it out, the problem is still there. Is there a reset button or something?\015

Answers :

Remove the five screws from the baseplate and replace your belt by removing your brushroll, putting the belt over the motor pulley, and then over the pulley on the brushroll, then replacing the brushroll in its original position and screwing the baseplate on. Note that you should make sure that the bearing ends of your brushroll spin freely prior to doing this to avoid the belt breaking again.
\015\012
\015\012-R
Repair Help & Product Troubleshooting for Oreck Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Oreck vacuum cleaner will only stay on in the upright position. If I try to recline it to vacuum, it shuts off...put it back up and it turns back on. Of course I can't vacuum in the upright position...what do I do?


It sound as if you have a short in the cord or it has come loose from the motor you can take it part by removing the four screws in the buttom of the base plate to see if any of the wires are loose. ... Oreck Vacuums

How to unclog the Oreck XL upright? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

Replacement brush for Oreck ProPower Plus - Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright


... Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright

Oreck xl 2100 vacuum belt keep on slipping - Oreck Xl 2100 Bagged Upright Vacuum


... Oreck Xl 2100 Bagged Upright Vacuum

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck vacuum keeps turning off - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

Oreck upright hard to push - Oreck XL2000 Bagged Upright Vacuum


If hard to push, only a few things to check:\015\012\015\012(1) Rear wheels will get hair or thread wrapped around axles, dust, etc. and be hard to turn. Make sure each wheel turns easily.\015\012\015\012(2) Small wheels on ne ... Oreck XL2000 Bagged Upright Vacuum

Oreck propower brush not turning - Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright


... Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright

Sock stuck in oreck vacuum - Oreck XL2000 Commercial Upright Vacuum, XL 2000


... Oreck XL2000 Commercial Upright Vacuum, XL 2000

How to disassemble oreck xl 21 vacuum - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck upright brushes not spinning - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Is there a reset switch on the Oreck vacuum? - Oreck XL2200 Bagged Upright Vacuum


No.\015\012\015\012If the unit is not running at all, this is a 2 speed unit, right? I'd check for a failure of the diode that provides the 2 speed action.\015\012\015\012Next likely failure is a broken wire at motor. ... Oreck XL2200 Bagged Upright Vacuum

Oreck xl upright vacuum. dropped it, not won't


... Oreck XL Ultra Bagged Upright Vacuum

Schematic for oreck xl 9100c - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck has become hard to push on rugs - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

Oreck xl21 motor wiring diagram - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Installing roller brush for oreck XL 21 - Oreck XL Ultra Bagged Upright Vacuum


Uh, probably not sure what the issue is, but \015\0121. unplug unit.\015\0122. Remove the multiple screws from the bottom of the unit.\015\0123. remove the bottom baseplate (usually black)\015\0124. the brush roll is now visib ... Oreck XL Ultra Bagged Upright Vacuum

The bar on my oreck doesnt turn - Oreck XL Ultra Bagged Upright Vacuum


1) test the belt drive for worn or broken or crack2) bearing bar defective.LUBE 3) debris in the bar4) motor defective repairsee the diagrams. God bless you ... Oreck XL Ultra Bagged Upright Vacuum

My oreck xl will not unlock - Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum


... Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum

My plastic bag holder came off oreck xl - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Vacuum hard to push - Oreck XL21 Bagged Upright Vacuum


You probably have a broken belt. replace it ... Oreck XL21 Bagged Upright Vacuum

How do i stop dust coming out of vacuum - Oreck XL Ultra Bagged Upright Vacuum


Change the bag. ... Oreck XL Ultra Bagged Upright Vacuum

I own an Oreck 2310RS upright vacuum cleaner. The cord is too short for my needs. The cord I need is a two wire 25 to 30 foot cord. Where can I buy this vacuum cord and how do I connect it? Thanks, Don


You can buy one at a oreck store but i would tell you to use an extention cord ... Oreck XL2200 Bagged Upright Vacuum

Vacuum is not turning on - Oreck XL Ultra Bagged Upright Vacuum


Try a ruling out a couple of things first before opening up the handle:\015\012\015\0121) First lets make sure your outlet has power\015\012 a) can you plug anything else in and have it work?\015\012 b) is the vacuum plugged ... Oreck XL Ultra Bagged Upright Vacuum

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0784 seconds