Having problems with your Oreck XL2000 Bagged Upright Vacuum ?

My Oreck has in the last 2 weeks become very hard to push on carpet , ok on bare floors. Thanks


Answers :

Look at 3 things:
\015\012(1) is there something wrapped around the rear
\015\012wheels or axles?
\015\012(2) Is there something wrapped around the small, front wheels or axles. (not likely this is the culprit.)
\015\012(3) Is your brushroll still turning. (This requires looking underneath while unit is on, have someone else nearby to pull the cord from wall, turn on & off quickly and make sure brush roll spins.
\015\012
\015\012If it is rear wheels, you can pop them out if necessary to clean the debris, they may be hard to press back in. Similar for the small front wheels, don't loose the axles. If brush roll is issue, check belt, insure that brush roll will spin freely and does not have debris wrapped around it.
Repair Help & Product Troubleshooting for Oreck XL2000 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Oreck has in the last 2 weeks become very hard to push on carpet , ok on bare floors. Thanks


Look at 3 things:\015\012(1) is there something wrapped around the rear \015\012wheels or axles?\015\012(2) Is there something wrapped around the small, front wheels or axles. (not likely this is the culprit.)\015\012(3) Is yo ... Oreck XL2000 Bagged Upright Vacuum

When i set it on carpet instead of bare floor it is hard to push when i vacume (when i turn nob it only has two settings floor and carpet no high pile or low pile)


Hi there,Sorry to hear you're having difficulties using your DC14 on this particular carpet. You may want to contact your carpet manufacturer to check it's suitable for cleaning with a vacuum cleaner equipped with a revolving brush. Manuf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.


Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I bought Roomba 560 robot vacuum cleaner about 3 weeks ago and it has been cleaned without problem all kind of positions of floors (also carpets) Last friday I anyway mountained nearby of outcoming door the black carpet. Now the situation is that Roomba doesn't move and clean above of this carpet. What is the reason and how to solve it ... ?.


Ok, take regular WHITE paper. Do not press it on the sensor, just make it long enough so it covers the sensor. Then, take some clear tape, and tape the piece of white paper over it. Watch for the wall brush and stuff, don't get it to close to them or ... iRobot Roomba 560 Robotic Vacuum

I have a windtunnel upright self-propelled that is very difficult to push, on carpet or hard floors. Seeems that it is stuck to the floor and at times you can smell the rubber from the belts. What could be the problem or problems?


Raise the front. you are trying too hard ... Vacuums

My dyson dc17 is very hard to push on a hardwood or carpet floor. When I take the canister off and push it while on it works great, so I figure the canister is giving me the issue. What o I fix? Thanks


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The vacuum is very hard to push on carpeting even when on hard floor level.


... Hoover Tempo Widepath Upright Vacuum - Blue

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900


Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Stripped gear noise occurs in carpet mode, not bare floor mode


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc41 hard to push on floor even with brush bar off, ok on carpet


... Vacuums

Oreck xl commercial spits out dust on bare floor but work on carpet. It is about 15 years old. Bag has been changed. Brushes are spinning so belt is working. Started about 2 weeks ago. HELP!


It might be that the beater brush is spinning when you tip it up to look at it but slight pressure of it contacting the floor is enough to stop it.\015\012If it were my machine I would remove the beater brush and clean it as best I could, paying part ... Oreck XL Ultra Bagged Upright Vacuum

New windtunnel bag vacuum worked fine for about a week but now is unbelieveably hard to push at same setting on same carpet as before.


The self propelled unit might have broken, their is a metal wire that helps make unit work correctly ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

We have a Dyson for several years and now it is very hard to push. In fact the front edge seems to be digging into the carpet as if it is a snow plow. Is Dyson a piece of **** and only lasts a few years ?


It probably needs a new brush roll. Not surprising after "several years". On some models it's advisable, or even essential, to fit a new soleplate at the same time. An easy job and not too costly. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dirt devil breeze with automatic height adjustment has become hard to push on carpet. How do I fix that?


... Dirt Devil M082550 Breeze Bagless Canister Vacuum

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Oreck has become very hard to push across carpet


IF IT PUSHED EASILY ON THE SAME CARPET BEFORE, THEN THE BRUSHROLL IS NO LONGER CONTACTING THE CARPET IT USED TO. A NEW BRUSHROLL AND/ OR BELT SHOULD GET YOU MOVING AGAIN. TRY THE BELT FIRST, MUCH CHEAPER.\015\012\015\012IF YOU HAVE RECENT ... Oreck XL Deluxe U3700 Bagged Upright Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?


Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

I have a Lux Floor Pro Heavy Duty carpet cleaner. Whis attachments (scrubbers) do I attach to the bottom to wash a non-plush carpet. I have three attachments that have hard bristles and three that have soft bristles (they look like hard floor attachments). When I used the ones with hard bristles it sounded funny


NEVER USE THE HARD BRUSHES ON CARPET ! You can burn up your motor, break the drive belt,or strip the drive gears The black bristle brushes are for all carpet types. \015\012The hard bristle brushes are made for hardwood and other smooth ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Dyson suddenly hard to push on carpet


I know this sounds silly, but it works. Turn it over and wipe all the black residue off the bottom of it (off the plastic on the bottom that rubs on the carpet as you push and pull it). I thought my husband was out of his mind when he told me that ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson animal D28 suction on floor vacuum mode is so strong I can't push the machine. Last used for hand tools, is there some mechanism that is stuck?


... Vacuums

Dyson dc41 hard to push on hardware floor


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Oreck XL 7000 is hard to push through a modest pile carpet. They gave us a shag attachment but all that does is push the carpet down. It is not ususable for us with bad backs etc.


... Oreck XL2200 Bagged Upright Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0526 seconds