Having problems with your Oreck XL2000 Bagged Upright Vacuum ?

Brushs arc against spinning motor - Oreck XL2000 Bagged Upright Vacuum


Answers :

Repair Help & Product Troubleshooting for Oreck XL2000 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushs arc against spinning motor - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

Oreck upright brushes not spinning - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

The brushes are not spinning - Oreck XL® Classic Bagged Upright Vacuum


It sounds to me that the drive belt to the brush is broken. To verify, or replace, you must take off the bottom cover. ... Oreck XL® Classic Bagged Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck upright hard to push - Oreck XL2000 Bagged Upright Vacuum


If hard to push, only a few things to check:\015\012\015\012(1) Rear wheels will get hair or thread wrapped around axles, dust, etc. and be hard to turn. Make sure each wheel turns easily.\015\012\015\012(2) Small wheels on ne ... Oreck XL2000 Bagged Upright Vacuum

Brushes don't move. vacuum motor works - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum


The brushes on the roller are driven by a wide, short rubber belt. These belts get old, worn, overheated, and break periodically.It should be a fairly simple matter to unscrew & remove the plate, revealing the belt and roller assembly. Yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Oreck xl21 motor wiring diagram - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Diagram for motor wiring oreck - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck xl gold roller brush not working - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

How to remove oreck 2605 hh motor - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Makes a clicking sound when vacuum spinning - Oreck XL® Platinum Pilot Bagged Upright Vacuum


... Oreck XL® Platinum Pilot Bagged Upright Vacuum

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem


... Oreck XL2200 Bagged Upright Vacuum

Oreck has become hard to push on rugs - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

Installing roller brush for oreck XL 21 - Oreck XL Ultra Bagged Upright Vacuum


Uh, probably not sure what the issue is, but \015\0121. unplug unit.\015\0122. Remove the multiple screws from the bottom of the unit.\015\0123. remove the bottom baseplate (usually black)\015\0124. the brush roll is now visib ... Oreck XL Ultra Bagged Upright Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums


Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Brush motor does not turn on - Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum


You could check Sears.com and click on parts then type in Model # or Part # this will get you a parts list you can choose from. ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Latch pin keeps spinning off belt door? - Oreck XL21 Bagged Upright Vacuum


The only correct solution is to replace the door. A small piece of tape works well too ... Oreck XL21 Bagged Upright Vacuum

Turn on motor just humms - Oreck XL2800 Bagged Upright Vacuum


If the motor is actually running and not picking anything up, I would believe it to be either a broken drive belt for the beater brush or the beater brush is frozen or both.\015\012Remove the beater brush and clean, paying special attention to the en ... Oreck XL2800 Bagged Upright Vacuum

Brush roller going backward - Oreck XL Ultra Bagged Upright Vacuum


Check that the wires are properly connected if the wires are crossed to the motor it will cause this effect ... Oreck XL Ultra Bagged Upright Vacuum

The brush does not spin when shapmooing - Kirby Ultimate G Bagged Upright Vacuum


Turn it upside down, see if you can the belt that driven up the motor gear, maybe it is mis allign or loosen. if it need a replacement then have it replace ... Kirby Ultimate G Bagged Upright Vacuum

Belts keep burning up when i turn it on - Oreck XL2000 Bagged Upright Vacuum


The brushes probably have strings or excesive carpet fibers where where it meets the base of deck and the cover remove screws from bottom pop out brushes and remove string and reasimble ... Oreck XL2000 Bagged Upright Vacuum

Brush doesn't rotate - Oreck XL Ultra Bagged Upright Vacuum


If the brush don't rotate.the first thing you need to do is check to make sure there is nothing jammed in the brush.Like a piece from a carpet,or hair.If it still don't work.then you need to change the belt inside the vacuum itself. ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1122 seconds