Having problems with your Oreck XL21 Bagged Upright Vacuum ?

Shag carpet problem with shag carpet, The oreck xl21 will not pull it's self.

Answers :

Repair Help & Product Troubleshooting for Oreck XL21 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shag carpet problem with shag carpet, The oreck xl21 will not pull it's self.

... Oreck XL21 Bagged Upright Vacuum

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.

Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.

The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

I don't feel that the vac is close enough to the carpet anymore .. it's almost like I have to push the head down so it reached the carpet to roll the brush through it ... I've tried a friends vac and it shows nicely that you've just vacuumed the carpet .. heavy traffic areas are not getting pulled back up .. I have the short shag type carpet .. Thanks

Consider disassembling and cleaning your unit. Sometimes dirt and grit will build up, and when wiped away allow the moving parts to function better. Dysons are made to be broken down by the homeowner. A manual can be obtained here: http://www.manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a windtunnel upright self-propelled that is very difficult to push, on carpet or hard floors. Seeems that it is stuck to the floor and at times you can smell the rubber from the belts. What could be the problem or problems?

Raise the front. you are trying too hard ... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum

My Oreck XL 7000 is hard to push through a modest pile carpet. They gave us a shag attachment but all that does is push the carpet down. It is not ususable for us with bad backs etc.

... Oreck XL2200 Bagged Upright Vacuum

My Oreck is hopping on my carpet while vacuuming. It is fine when pushed away - it hops and leaves marks on my carpet when I pull it back. I have changed the bag and cleaned off the roller and checked for a clog. All are fine.

My first thought is to change the belt.If it is stretched this is a common symptom.You can go to youtube and my chanell is sewvacmd.Their is a video on how to change it.Hope this helps. ... Oreck XL2200 Bagged Upright Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I've only used it a couple times and I don't see where it is working. Has anyone else had this problem?

Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected in ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I am having those same problems , brushes are not agitating . leaking water from the bottom of the unit , the suction is week it is not pulling the water out of the carpet .

... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900

Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

My oreck xl21 is so hard to push on my middle lenth carpet that the unit is not usable. Help.

... Oreck XL21 Bagged Upright Vacuum

Bissell 7901-1 The soap doesn't mix with the water when I pull the trigger, I can see the soap isn't being used when I do the carpets. What can I do, have no problem taking this machine apart.

If the mix valve knob is turning smoothly, then most likely the cap and valve for the sop bottle is bad. Also make sure that the seal is on the cap at the bottom of the bottle and not sitting in the hole. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage

If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?

You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Why does my Oreck drag on carpeting? bought an Oreck upright 4.8 bagless at a garage sale. Great on the kitchen floor but seems to drag , difficult to push on the commercial carpeting. any hints

... Oreck Dual Power Electric Floor Sweeper Bagless Upright Vacuum

I have a problem with Vax Rapide Ultra 2 carpet washer

... VAX Appliances Vacuums

Oreck xl21 motor wiring diagram - Oreck XL21 Bagged Upright Vacuum

... Oreck XL21 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0543 seconds