Having problems with your Oreck XL21 Bagged Upright Vacuum ?

How do I replace the micro blade - Oreck XL21 Bagged Upright Vacuum


Answers :

Repair Help & Product Troubleshooting for Oreck XL21 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I replace the micro blade - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Oreck upright brushes not spinning - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Oreck xl21 motor wiring diagram - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Oreck xl21 loose handle - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

Vacuum hard to push - Oreck XL21 Bagged Upright Vacuum


You probably have a broken belt. replace it ... Oreck XL21 Bagged Upright Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

MANUAL ORECK XL21 - Oreck XL Ultra Bagged Upright Vacuum


The Oreck XL21 is a refurbished XL vacuum. All Oreck manuals are available here: http://www.oreck.com/Product-User-Guides/global-user ... Oreck XL Ultra Bagged Upright Vacuum

Has power but won't turn on - Oreck XL21 Bagged Upright Vacuum


Sounds like either a bad switch,bad wire or a bad motor -- use a volt meter to trace power out to find what is at fault.\015\012if it turns out to be a bad motor or switch -- you can get the replacement parts at your local vacuum repair shop. ... Oreck XL21 Bagged Upright Vacuum

Not driving forward - Oreck XL21 Bagged Upright Vacuum


Change the belt ... Oreck XL21 Bagged Upright Vacuum

How do you remove the handle to clean it? - Oreck XL21 Bagged Upright Vacuum


I am unsure why you would be removing the handle to clean it. It really is not necessary, but the handle grip is held together with 6 screws, take out the screws the two halves come off of the handle pipe.\012 \012 ... Oreck XL21 Bagged Upright Vacuum

Replace fan blade e77491 - Kirby Generation 3 Bagged Upright Vacuum


KIRBY VACUUM REPAIR HOW TO REPLACE THE FAN IMPELLER ... Kirby Generation 3 Bagged Upright Vacuum

How to replace brush roller? - Oreck XL Ultra Bagged Upright Vacuum


Turn your vacuum over and there should be 5 or 6 Phillips screws that hold the base plate on. Take out those screws and that will give you access to where the brush roller is located. If you are replacing the roller it would be a good idea to repla ... Oreck XL Ultra Bagged Upright Vacuum

Replace Kirby legend II fan (impeller blade) - Kirby G4 Bagged Upright Vacuum


In order to replace the fan you will buy a 2 or three piece lexan fan kit containing the fan a spacer and shaft. You must remove the carpet head and then looking from the back of the machine you will find a series of philips screws on the oute ... Kirby G4 Bagged Upright Vacuum

How to remove base plate - Oreck XL21 Bagged Upright Vacuum


Here is the manual with full instructionshttp://dem ... Oreck XL21 Bagged Upright Vacuum

Latch pin keeps spinning off belt door? - Oreck XL21 Bagged Upright Vacuum


The only correct solution is to replace the door. A small piece of tape works well too ... Oreck XL21 Bagged Upright Vacuum

Is there a reset switch on the Oreck vacuum? - Oreck XL2200 Bagged Upright Vacuum


No.\015\012\015\012If the unit is not running at all, this is a 2 speed unit, right? I'd check for a failure of the diode that provides the 2 speed action.\015\012\015\012Next likely failure is a broken wire at motor. ... Oreck XL2200 Bagged Upright Vacuum

How to disassemble oreck xl 21 vacuum - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

How do you install oreck bag docking system - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck Inner Bag doesn't stay connected - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

How to unclog the Oreck XL upright? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??


... Bissell 3510 PowerPartner Upright Vacuum

My plastic bag holder came off oreck xl - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Miele vacuum bag holder replace - Miele S7280 Bagged Upright Vacuum


... Miele S7280 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1317 seconds