Having problems with your Oreck XL21 Bagged Upright Vacuum ?

How do I remove the baseplate of my Oreck XL 21?

\015 I unscrewed the screws on the bottom of my Oreck XL 21 and the bottom won't come off.\015

Answers :

Repair Help & Product Troubleshooting for Oreck XL21 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I remove the baseplate of my Oreck XL 21?


... Oreck XL21 Bagged Upright Vacuum

Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?


You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum

Oreck XL My Oreck just turned off in the middle of vacuuming and I smelled a burning smell. I am thinking that if I can take it apart and remove whatever turned it off, it will run again.


Your roller brush is probably bound with hair and is not able to move ... Oreck XL2600 Vacuum

How to remove oreck 2605 hh motor - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Remove cord on oreck xl - Oreck Lower Cord Xl9800/2700/2610 7508102


... Oreck Lower Cord Xl9800/2700/2610 7508102

Oreck XL9100 Our vac motor was removed to remove a hairpin in the motor.? The tape fell off the wires. Do you have a wiring diagragm?


See diagrams ... Oreck XL Ultra Bagged Upright Vacuum

Base Plate screw rotating in insert and not coming out. Insert come unfixed with screw still attached. Therefore unable to remove baseplate, unable to remove cotton fibres from brushes. Have you an engineer in the vacinity of york(NOT A SALESMAN WITH A FRANCHISE) PLEASE


Try to remove all other base plate screws first. If they can be removed gently try to pull open by hand against the lid while rotating the remaining screw. You will need to apply outward pressure betweent the insert and baseplate to remove it while r ... Vacuums

Can't remove bottom plate to change broken belt on oreck xl instashield vacuum ...i think i removed required screws


... Oreck Vacuums

How do I remove the outer bag from my Oreck XL2 upright


... Vacuums

How do I remove bottom panel on oreck halo?


... Oreck HALO100 Bagged Upright Vacuum

How do you remove fan off motor oreck xl9800


... Oreck XL2200 Bagged Upright Vacuum

How to remove shake out bag on oreck commercial or101


... Oreck Commercial OR101H HEPA Commercial Vacuum

Oreck xl 9300 can not remove seal cup to change fan - appears glued?


You should be able to prise it of it will just be a push fit see link belowhttp://www.vacpartswarehouse.com/Oreck-XL9300-s/2925.htm ... Oreck Vacuums

Oreck xl 3700hh baseplate repair


... Vacuums

How do I remove the bag - Oreck XL2200 Bagged Upright Vacuum


Unzip cloth bag look at paper bag it may have a spring loaded mech. holding it or it just snaps in place look at your replacement bag to see if its slotted it probably snaps into place watch how you remove the old bag and repeat the process ... Oreck XL2200 Bagged Upright Vacuum

I have an oreck xl 2200 with the bag docking system. Can you remove this to use the standard bags without the docking system?


No decause there would be no way of holding the bag in ... Oreck XL2200 Bagged Upright Vacuum

HOW DO YOU REMOVE THE BASEPLATE ON THE HOOVER ZOOM


I LOGGED IN TO THE HOOVER SIGHT AND FOUND THE INFORMATION THERE ... Hoover Vacuums

How do you remove the handle to clean it? - Oreck XL21 Bagged Upright Vacuum


I am unsure why you would be removing the handle to clean it. It really is not necessary, but the handle grip is held together with 6 screws, take out the screws the two halves come off of the handle pipe.\012 \012 ... Oreck XL21 Bagged Upright Vacuum

Removing fan housing from oreck xl21 does not appear to be a nut holding the housing


... Oreck Vacuums

How to remove base plate - Oreck XL21 Bagged Upright Vacuum


Here is the manual with full instructionshttp://dem ... Oreck XL21 Bagged Upright Vacuum

I would really like to wash the outer bag of my vacuum, but I have a problem. I can remove the outer bag from the vacuum, but the plastic 'frame' that is inside the outer bag is sewn to the bag. So what am I supposed to do about that if I want to put it in the washing machine? I have the Oreck XL Silver.


Hi, you can wash the bag. However you cannot wash the bag in the wash machine. What you will want to do is look for the screw or depending on the model, untwist the cap down on the rod next to the machine. that entire pole section will co ... Oreck XL2000 Bagged Upright Vacuum

How do I properly remove the fan from an Oreck XL9200s upright vacuum? It looks all chewed and beat up.


You will need to grip the motor shaft with a vise grip or similar with a pad underneath so as not to score the shaft , which in tun would damage the belt. A piece of tire tube or leather will help. The fan is threaded and will rotate off oppos ... Vacuums

I have to replace the motor brushes in my Oreck XL model 2000RH. How do I remove the old brushes?


If it's an AC induction motor there are no brushes. ... Vacuums

How do you remove the bag docking system from an oreck to replace it?


At the point where it hinges squeeze the two arms together and they should dis-engage from the part that holds the bag and then spread the two arms to dis-engage the upper part from the nozzle on the handle. ... Oreck XL2200 Bagged Upright Vacuum

How do you remove outer bag for cleanin/ - Oreck XL2600 Vacuum


... Oreck XL2600 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0411 seconds