Having problems with your Oreck XL21 Bagged Upright Vacuum ?

Where do the cotter pins go on an Oreck upright vacuum? Thanks. Sally from Lake County, Ohio


Answers :

I called the Oreck Company in the late night. They are in service 24/7. The employee instructed me on where the cotter pins are attached. Glad to help someone.
Repair Help & Product Troubleshooting for Oreck XL21 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where do the cotter pins go on an Oreck upright vacuum? Thanks. Sally from Lake County, Ohio


I called the Oreck Company in the late night. They are in service 24/7. The employee instructed me on where the cotter pins are attached. Glad to help someone. ... Oreck XL21 Bagged Upright Vacuum

Latch pin keeps spinning off belt door? - Oreck XL21 Bagged Upright Vacuum


The only correct solution is to replace the door. A small piece of tape works well too ... Oreck XL21 Bagged Upright Vacuum

Oreck upright hard to push - Oreck XL2000 Bagged Upright Vacuum


If hard to push, only a few things to check:\015\012\015\012(1) Rear wheels will get hair or thread wrapped around axles, dust, etc. and be hard to turn. Make sure each wheel turns easily.\015\012\015\012(2) Small wheels on ne ... Oreck XL2000 Bagged Upright Vacuum

Oreck propower brush not turning - Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright


... Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright

Oreck upright brushes not spinning - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

How to unclog the Oreck XL upright? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

Replacement brush for Oreck ProPower Plus - Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright


... Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Why does my Oreck drag on carpeting? bought an Oreck upright 4.8 bagless at a garage sale. Great on the kitchen floor but seems to drag , difficult to push on the commercial carpeting. any hints


... Oreck Dual Power Electric Floor Sweeper Bagless Upright Vacuum

Oreck has become hard to push on rugs - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

How to disassemble oreck xl 21 vacuum - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Sock stuck in oreck vacuum - Oreck XL2000 Commercial Upright Vacuum, XL 2000


... Oreck XL2000 Commercial Upright Vacuum, XL 2000

Schematic for oreck xl 9100c - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Installing roller brush for oreck XL 21 - Oreck XL Ultra Bagged Upright Vacuum


Uh, probably not sure what the issue is, but \015\0121. unplug unit.\015\0122. Remove the multiple screws from the bottom of the unit.\015\0123. remove the bottom baseplate (usually black)\015\0124. the brush roll is now visib ... Oreck XL Ultra Bagged Upright Vacuum

The bar on my oreck doesnt turn - Oreck XL Ultra Bagged Upright Vacuum


1) test the belt drive for worn or broken or crack2) bearing bar defective.LUBE 3) debris in the bar4) motor defective repairsee the diagrams. God bless you ... Oreck XL Ultra Bagged Upright Vacuum

My Oreck will not unlock - Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum


Try an other key. ... Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum

My Oreck vacuum cleaner will only stay on in the upright position. If I try to recline it to vacuum, it shuts off...put it back up and it turns back on. Of course I can't vacuum in the upright position...what do I do?


It sound as if you have a short in the cord or it has come loose from the motor you can take it part by removing the four screws in the buttom of the base plate to see if any of the wires are loose. ... Oreck Vacuums

Is there a reset switch on the Oreck vacuum? - Oreck XL2200 Bagged Upright Vacuum


No.\015\012\015\012If the unit is not running at all, this is a 2 speed unit, right? I'd check for a failure of the diode that provides the 2 speed action.\015\012\015\012Next likely failure is a broken wire at motor. ... Oreck XL2200 Bagged Upright Vacuum

Oreck XL suddenly lost power - Oreck XL Ultra Bagged Upright Vacuum


Wiring in handle has loose connection or the brushes in the motor needs replacing. cost $18 for new ones. ... Oreck XL Ultra Bagged Upright Vacuum

My Oreck Upright will not stay upright! The handle falls over everytime I leave it stand on its own.


What you are in need of is what they call a detent. There is a possibility that is has broken off from the housing which means that the only way to repair it properly is to replace the entire housing. It may have just had the screw come loose and h ... Oreck XL® Classic Bagged Upright Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

My plastic bag holder came off oreck xl - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!


... Sharp Twin Energy EC-TU2607 Vacuum

Our oreck upright sweeper is so hard to push on the carpet, why? its an oreck xl2 celoc hypo-allergenic plus and the probem occurs every time we use it. we didn't know there was a belt on it.


Change the roller brush ... Oreck XL21 Bagged Upright Vacuum

Oreck xl21 motor wiring diagram - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0561 seconds