Having problems with your Oreck XL2200 Bagged Upright Vacuum ?

The vacuum won't turn on. It"s an upright,and the power light on the on/off switch is lit, but no power to the unit below.

Answers :

Check that you have power at the motor with a tester 0-200v .If you have it could be brushes or u/s motor.If not check power out from the switch ,if ok you you need to replace cables.
\015\012Please leave a positive feed back for me if this helps and get back to me if you need more help
Repair Help & Product Troubleshooting for Oreck XL2200 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The vacuum won't turn on. It"s an upright,and the power light on the on/off switch is lit, but no power to the unit below.

Check that you have power at the motor with a tester 0-200v .If you have it could be brushes or u/s motor.If not check power out from the switch ,if ok you you need to replace cables.\015\012\015\012Please leave a positive feed back for m ... Oreck XL2200 Bagged Upright Vacuum

I have a hayden premier supervac central vac system, while working on the switch in for the beater bar, the actual unit has turned off, the green light is no longer lit, is there a fuse on it somewhere or a reset button, i have tried unplugging it and replugging it in, but can not seem to get it to power up now?

Should be a reset on the main unit near the top ... Vacuums

Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.

... Euro-Pro S3325 Handheld Steam Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum

Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?

... Miele s558 Silver Moon Vacuum

Unit has power from Plug to unit. Current flows all the way to switch and switch seems to be ok but unit will not turn on. Wife says it was cutting on and off when moving it around. Checked conntec

You either have a bad switch oir you have a short in the cord.plug it in and turn it on then move the cord around from top to bottom and see if it acts up..if not tap on the switch afew times and if it cuts out then the switch is bad.try to plug it i ... Vacuums

The unit does not start when I turn on the switch on the handle. The power nozzel runs, but the vacuum motor does not. The reset button is not popped, there is 110volts to the unit, and I tried flicking the switch inside the unit underneath the filter with no responce.

... Electrolux Centralux Vacuum

I own a Sanyo 35s 3.5 Rice cooker that has stopped cooking and heating. Power is going to the unit power light comes on. We have checked to make sure that the unit was turned off before unplugging as per the instuctions. Unit was new in Feb 2010 and well taken care of. Anything we are missing here?

If you have been washing or scratching the inner pot with something sharp or harsh like a metal spoon or hard sponge it could cause that and even electric shocks. try changing the pot ... Vacuums

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you

Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

Electrolux epic series 6000 sr model canister...we put a new bag in machine but it wont turn on and the light is on saying the bag is full and needs to be replaced...we tried the on-off switch several times but it wont turn on...why?

... Electrolux Vacuums

The microwave will not turn on. No power. Checked fuse box and power outlet...not the problem. Unit just wont turn on? Is there a reset button or another option.?

Remove the cover and locate the internal fuse you will find near the power cord entry. Replace with the same. ... Vacuums

We recently bought a home with a 52" Hampton Bay Berlini Model 729 395 ceiling fan with a light that operates on a remote control. There is also a wall switch plate with two circular controls - one pushes and spins, the other turns with 4 clicks. We can not get the light or the fan to operate using either the switches or the remote. We have checked the circuit breaker. The manual that came with the unit - provided to us from the previous homeowner - really only describes how to install the uni

Nancy do you want to sell the Berlini fan if youstillo have it? ... Vacuums

I have a Casa Blanca Intelitouch ceiling fan. Panama5 12004T model no.?? serial no.: AU16550 A casa blanca tri-switch on the wall: lights-fan-power When I turn it on, the lights and fan work fine. After a period of time, the lights go off by themselves. I don't remember the fan ever going off by itself, only the lights.

The light are going off only because after a period of time the circuit lets off the trigger on the switching thyristor. So the fault is within the control box of the unit which must be taken out to confirm.\015\012Now attempt to do the job onl ... Vacuums

My Prosine 2.0 display panel displays Panel Fault: Memory error and the display error as well as all LEDs are off. The unit looks as if it has no power to it. I reset (power off.power on) the Prosine and all LEDs on the display (except for the back lit display) turn on for about 3 seconds then all go off again. I am able to use 120v RV Resort power and all 120v equip works. The Coach batteries do not charge and were low. I charged the Coach batteries with an external charger. The charge works ye

... Vacuums

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob

Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum


... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

Wont charge new roomba for xmas. lights on charging unit both flashing but no power in roomba. it worked yesterday when i got it out of the box and did a full clean. i feft it on charge over night ready for the clean today but when i got up no power atall please can you offer a solution. i have held down pock and start - no joy. i have checked the battery connections - no joy please help many thanks caroline

Did you try plugging in 560 driectly to charger then run it? ... iRobot Roomba 560 Robotic Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.

The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

My Kirby G 2001 upright vacuum wont turn on. I tried another outlet and still nothing. I don't see a breaker switch anywhere. If you know of any common problems I would love to hear them. I am very mechanically inclined, I just was wondering if there are any common issues with the motors or power switches etc. so I don't waste a lot of time troubleshooting. Thanks

This might sound a bit silly but check to see if the cord is plugged into the machine correctly if it is check to see if the safety interlocks are all engaged. ... Vacuums

I have a Hayden SuperVac 3600, almost 10 years old. The unit still runs, but now when I switch to the power nozzle, it doesn't have power to turn that. I think this happened once before and maybe they replaced a circuit board(?). We took it to a local repairman this time and he says he can fix it temporarily with a new cartridge, but that he won't promise it won't happen again soon.....

The hose has fuseable link inside, generally a 3-7 amp. It is at the wall end underneath the hose cuff. Easy to replace as it crimps in line. If you have a meter you can also test the detachable hose to wall cord for continuity, then check the hose t ... Hayden Industries SuperVac 6000 Central System Vacuum


Is the power light pulsing when on charger? Make sure you have the battery in correctly and snapped securely into place. Only charge on the home base, do not plug in directly. ... Roomba Robotic Floor Bagless Vacuum

Motor wont turn on.I checked the switch and I think it is working.motor turns on if a put direct power to it.'but it smokes at the brushes. can you help?

This sounds like either the belt isn`t on right or the brush is not slotted in the vacuum right remove the plastic or metal cover from the bottom and check by inspecting the belts ability to easly turn the brush rod check with your hands DO NOT turn ... Kirby G4 Bagged Upright Vacuum

I have a Hampton Bay ceiling fan St. Regis model #138 498. Somehow the remote got messed up and now the lower light flashes on/off when the power is on and nothing else works. This happened one other time and I simply turned off the switches and when they were turned back on everything worked fine. This fix does not work this time.

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0810 seconds