Having problems with your Oreck XL2200 Bagged Upright Vacuum ?

Reassemble of handle on upright

\015 I have a L shape wire left over on reassemble of my handle on my upright oreck. One end hooks into a hole on the handle shaft where does the other end go?\015\012Doc\015

Answers :

Place handle half with the posts that hold the screws facing up.
\015\012silver pole with hole that goes completely throuigh goes over lower screw post (Long side)
\015\012static wire - L shaped end goes in small hole on opposite side of handle just below
\015\012vacuum switch hole, curve of wire should follow curve of handle and fits into top of
\015\012silver pole and pushes againt it providing push to hold siver pole.
\015\012hope this helps
Reassemble of handle on upright
\015\012Oreck XL 2200 Bagged Upright Vacuum
\015\012I have a L shape wire left over on reassemble of my handle on my upright Oreck. One end hooks into a hole on the handle shaft where does the other end go?

\015\012I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
\015\012I suggest that the upper handle for the Oreck XL2200 should just be help on by sliding the handle over the upper handle assm and there is one screw that you use to tighten the hand e to the upper section, the lower handle assm just slides in to the lower motor assm handle and so does the top. I was not aware of any wire for the handle assm. Feel free to contact the Oreck Corp factory phone number listed below or call your local vacuum dealer in the yellow pages.
\015\012 http://www.oreck.com Customer Service
\015\012Customer Service Hours:
\015\012Monday - Friday
7am - 7pm Central Time

8am - 4:30pm Central Time

8am - 4:30pm Central Time
Repair Help & Product Troubleshooting for Oreck XL2200 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Reassemble of handle on upright

Place handle half with the posts that hold the screws facing up.\015\012\015\012silver pole with hole that goes completely throuigh goes over lower screw post (Long side) \015\012\015\012static wire - L shaped end goes in smal ... Oreck XL2200 Bagged Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

I have a Kirby Heritage Vacuum Cleaner. Recently the handle fell backwords. I took the pin to the handle out and replaced it. It helped some, but the handle does not stay upright.

... Kirby Ultimate G Bagged Upright Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!

... Vacuums

My Oreck Upright will not stay upright! The handle falls over everytime I leave it stand on its own.

What you are in need of is what they call a detent. There is a possibility that is has broken off from the housing which means that the only way to repair it properly is to replace the entire housing. It may have just had the screw come loose and h ... Oreck XL® Classic Bagged Upright Vacuum

My beater bar will not spin when the handle is lowered? But there's suction thru the hose when the handles upright

I had the same problem. I read, earlier today, that one of the "problem solvers" called Dyson. Dyson suggested, with the Dyson upright and plugged in, on a carpet, toggle the "bare floor" / "carpet" knob from bare floor to carpet 5 times, then lay ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

I have lost the manual and forget how to use the hose part of vacuum, also the handle turns and is not secure ( that is the handle in the upright position). It is a bagless Stick Shark Vac. I need to know how to attach the hose to the vac so I can clean furniture and corners.

... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

Dyson DC28 handle stuck in upright position - Dyson Ball DC24 Bagless Upright Vacuum

You DO NOT have to take your machine to a "certified technician" to fix this problem. Stand behind your machine, lean over and look at the front: Right in the center of the opening between the machine and the beater bar head, you will see ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac

How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The metal rod inside the handle fell out when i separated the two handle parts to replace the square metal post/handle. I do not see a purpose for the metal rod or where it connects near the on/off switch. XL upright Oreck model.

It is like a static ground post your right it really dosent do anything ... Oreck XL2000 Bagged Upright Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it

The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

My Dyson DC17 Animal Bagless Upright does not click to stay in an upright position. It works but the handle falls to the floor.

This is a common fault with the Dyson DC07 (and other Dysons) unfortunately the clip that holds the handle upright hs broken. It can be repaired, but will cost a reasonable amount to have done... I would just live with the problem and prop the vacuum ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson d17 will only stay on if the handle is tilted back and it's not sucking at all....although it's running. When i stand the vacuum up with the handle upright, it cuts off.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My hoover upright powermate cyclonic vacuum came upplug in the handle how do I get the handle out so I can plug it back in the model number is U5182-900

There should be 2 to four screws on the backside where the handle meets the dirt catch area.take the screws out and the handle should slide off the top where the dirt cup is ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

Telescopic handle I don't think I have the exact same vacuum, although mine is a fantom upright bagless. I can't get the telescopic handle to stay in place. It pulls out whenever I try to pull back the vacuum. Any tips would be helpful! Thank you

Sometimes the locking mechanism for the wand wears out, make sure u have it all the way in and look where it locks and see if it looks worn ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Hi i have just been given a dysondc07 hepa could anyone tell me how to release the upright handle as to start hoovering it seems to be stuck upright thus unable to commence

Take off the power cord from its two hangers, depress the coloured clip above the power switch and the wand will lift out along with the back telescopic hose. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Electrolux Genesis 1572F: 1) One of the two spring/clips/whatever that hold the upright upright for storage has busted. What is the part called? Where might I find a spare? Or should I go to a machine shop? 2) The power cord retainer thingy on the back of the handle grip has broken; any idea about part#, name of part, where to look? (I can't find a manual or whatever, exploded parts diagram, etc., online. I guess this is the planned obsolescence thing--after all, the machine is hardly even 2

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.

Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

Bissell 6590 the part I am trying to replace allows you to lower the handle to lay flat to get under furniture and it also allows the handle to stay in the upright postion. i have looked on bissell.com and did not find it-but I will try again. you are super and Thanks allot . Have a super easy day! Michele

It is called the detent lever part # 2030052. If you can't order it from bissell.com or over the phone, most repair shops should be able to order it for you. ... Bissell 6590 CleanView Bagless Upright Vacuum

Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?

If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum

Motor loud I have a dyson dc17..recently when i turned it on and pulled the handle down to vacuum the motor was very loud..put the handle in the upright position it is quiet.any suggestions?

When you put the handle down it turns on the brush roll. you may need to clean the brush roll or replce it if the bearings are bad.also clutch and 2 belts are started when putting handle down for brush operation. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dirt Devil upright ddup1800 and it is stuck in the upright position. There is no switch or level. You stand on the front while moving the handle backwards to get it to move. However, not today. Help?

... Vacuums

I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.

This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.0611 seconds