Having problems with your Oreck XL2200 Bagged Upright Vacuum ?

How do i take apart the roller from my Oreck upright

\015 How do I take out the roller and how can I get to the fan belt to check to see if is working\015

Answers :

Repair Help & Product Troubleshooting for Oreck XL2200 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i take apart the roller from my Oreck upright


... Oreck XL2200 Bagged Upright Vacuum

How do I take oreck apart? - Oreck XL Ultra Bagged Upright Vacuum


5 screws on bottom plate. Then couple to hold fan housing and motor. Not a bad job just takes a little juggling finesse. ... Oreck XL Ultra Bagged Upright Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

I have a Royal upright metal vacuum. The roller stopped spinning. I took the roller off and the ends were full of dust and hair. I would like to take the ends of the roller off to clean more -- how do I do this?


... Royal 4000 Classic Bagged Upright Vacuum

I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap


... Oreck DutchTech DTX1300A Bagged Canister Vacuum

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do


I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

Oreck XL My Oreck just turned off in the middle of vacuuming and I smelled a burning smell. I am thinking that if I can take it apart and remove whatever turned it off, it will run again.


Your roller brush is probably bound with hair and is not able to move ... Oreck XL2600 Vacuum

Installing roller brush for oreck XL 21 - Oreck XL Ultra Bagged Upright Vacuum


Uh, probably not sure what the issue is, but \015\0121. unplug unit.\015\0122. Remove the multiple screws from the bottom of the unit.\015\0123. remove the bottom baseplate (usually black)\015\0124. the brush roll is now visib ... Oreck XL Ultra Bagged Upright Vacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!


The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Oreck xl gold roller brush not working - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

I have the Electrolux Intensity upright vacuum. The roller bar underneath that is used for carpet no longer turns. I have checked the belt that is attached to it. I'm afraid that it may be the motor. Where can I take it for service or shat do I do now? Kay


... Electrolux Vacuums

HOW DO I REPLACE A POWER CORD? HAVE THE CORD, DON'T KNOW HOW TO TAKE THE CASING APART ON POWERFORCE UPRIGHT


Push a SMALL screwdriver under the rubber handgrip. Put a fre drops of alcohol into the opening where the screwdriver is. This will llubricate the grip so you can get it off. After you repplace the wire, use alcohol to put the grip back on. It wi ... Bissell Vacuums

I have a Dirt Devil Upright Vacuum Model 088525B. I need to replace the power cord. How do I take the vacuum apart?


... Dirt Devil Vacuums

No suction I live in a house with two bernese mountain dogs... very large animals who shed a LOT.  I've cleaned the filters, the roller, and gotten as far into the hoses as I can without taking the entire machine apart.  It's still not cleaning as well as I know it can... nothing is making it into the debris receptacle.  What can I do?


Hi elora,\015\012\015\012I live in a house with three shedding cats. I also have the same vacuum. About twice a year, I have to getinto the area of the vacuum where the motor is. There is a little pring loaded vavle that sometimes gets ... Bissell 3590 CleanView Bagless Upright Vacuum

How to take apart to replace power cord - Miele S183 Powerhouse Bagged Upright Vacuum


Hello,In order to access the cord on the Miele S183 upright, you'll need to first remove the handle from the vacuum cleaner. There is a large screw that holds the handle in place that is located under neath of the lower cord wrap hook. ... Miele S183 Powerhouse Bagged Upright Vacuum

Dirt Devil bagless upright. sucks up dirt in the front and spits it out in the back. I have taken it apart to check for visible clogs in hoses and checked belt and rollers all of which are fine. what next?


There seems to be no vacuum drawing the debris away from the brush head. Remove the debris canister to check for air blowing into it. Check particularly, the area where the brush head pivots off of the upright portion. Hope this helps! ... Dirt Devil M110000 Bagless Upright Cyclonic Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.


May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Very little suction from vacuum is occurring after I pulled a string from the roller. Hot air is blowing out of unit. Was working fine until I pulled out a string...Suction is occurring from wand.The brushes now make a loud sound too when activated...do I have to take the unit apart to readjust them or something?


Yes re adjust ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

I need to take apart my Kenmore Progressive Bagless Upright with Inteli-Clean System


What problem are you trying to fix? The is no belt so you don't need to remove the bottom plate. If you are trying to remove the main hose, remove 4 screws on the back and remove the plate. There are 2 more screws under that. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

Have Kenmore Progressive Direct Drive upright. Roller not spinning. Have cleaned all debree with no luck. Took apart and discovered white plug disconnected from motor. No visible place to reinsert. Need assistance or skamatic


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Kenmore upright vacuum model 116.35923500. not rotating when on. Easy way to clean without taking apart?


There is a switch that tells the cleaner that the upright is locked \015\012upright and the beater bar won't spin until you depress the foot release\015\012 and tilt the cleaner. This switch mount is poorly designed, its just \015\012sitting in a poc ... Kenmore 22812 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0533 seconds