Having problems with your Oreck XL2200 Bagged Upright Vacuum ?

HOW DO i CLEAN MAIN TUBE IN HANDLE CLOGED

\015 NOT PICKING UP\015

Answers :

You'll have to unpick or slide up the rubber rings on the back of the handle at the bottom where the rear of the bag is. Unclip the bag so that it moves freely, slide up the rubber rings and you'll find a series of pop locks. Push these in to take out the main dust spine pipe - also remove the power cord at the top of the handle to release the handle. In the middle of the spine there is one screw that bonds the top handle part to the spine, unscrew this so that you can split the two parts up and check for clogs. Also check the main dust channel that leads to the bag - it is notorious for clogging because of its relatively small dust channel. 
Repair Help & Product Troubleshooting for Oreck XL2200 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HOW DO i CLEAN MAIN TUBE IN HANDLE CLOGED


You'll have to unpick or slide up the rubber rings on the back of the handle at the bottom where the rear of the bag is. Unclip the bag so that it moves freely, slide up the rubber rings and you'll find a series of pop locks. Push these in to take ou ... Oreck XL2200 Bagged Upright Vacuum

My attachments that twist to lock keep coming apart while I vacuuming. Mainly the angle tube and straight tubes. I've tried cleaning the tubes. How can I remedy this?


One line of black electrical tape on the piece that goes into the other piece should give you enough resistance to lock them into place. example, if you are connecting the tube to the angle piece, where the tube will go into the angle piece, you want ... Kirby G6 Bagged Upright Vacuum

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

I took apart my beam rugmaster plus model 045-322 and cleaned out "stuff". Now I can't figure out how to put one piece back in. Is there a diagram somewhere that I can look at? It consists of 2 pieces of metal that go to the right of the handle tube.


... Beam Industries Vacuums

Hi, I have an Upright Vacuum. Unfortunately, the box that contains the Dust container handle, and the Dust container pipe, has broken the base. It is right where we open it to clean the pipe. It is possible to buy the whole tube? Alicia


Hi, yes it is possible to buy the whole tube replacement but you have to get in touch with the manufacturer of the vacuum cleaner to make a request for the needed parts.Take care ... Vacuums

I have A Bissell power heat steam cleaner and tubes are clogged how do I get to 1 and how do I unclog them. It just stop spraying it will **** up but it will not spray out of the main part or out of the handle


Lisa: If anyone you know is mechanically inclined, they can open the machine using a screwdriver. follow the path the water takes in the tubes and find out where the water is being blocked. You'll know what to do to fix the machine when yo ... Vacuums

Need to replace the main belt on my Bissel 1698-P. Can't figure out how to get the belt around the brush roller. Have the top off. Cleaned the water tubes, didn't let the water come down.


Remove belt access door at left front of unit.\015\012\015\012Unplug the unit. Remove the two solution tanks.Remove spray tips from guides.Remove the brush and cog belt by removing the screw from the orange retaining collar.\015\012Remove belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I NEED TO CLEAN UPRIGHT HANDLE TUBE IT IS CLOGGED


Its a simple operation but it will take some time. \015\012On the back of the Oreck just up from the motor you'll come to the first rubber ring which hides the push/pin locks of the main spine. There are two or three on the Oreck depending on th ... Oreck XL2200 Bagged Upright Vacuum

I have a Eureka bagless, The Boss, there is a clog behind the top dirt catcher. I have cleaned every other tube, filter, clogs, etc.. I can't get my hand up into the main housing. Thank you so much! Sijai


Try using a straightened wire coat-hanger. You should be able to bend a small hook at the end of the wire, and then bend it to get to the clog. If you can get the clog to move a little, but can't get it all the way out, try putting the vacuum back ... Vacuums

How do you get the high reach cleaning tube to go back into the main unit?


... Dyson DC25 All Floors Bagless Upright Vacuum

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Electrolux Central Vac - very hot where tube attaches to handle


Yes definatly take it to a shop and have it looked at. if its not worth repairing they will let you know. ... Electrolux Central Vacuum

Cant get pin in kirby legend 11 handle,the main body seems to have shifted /


You will need mole grips to pull out handle pin. ... Kirby Heritage 2 and Legend Vacuum Cleaner Cord 32 ft Black, 192084

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.


Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.


You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

I have Bissell Model 1699-R Proheat carpet steam cleaner one of the tubings that connects into spray got mixed with some tubings during tubing replacment to the point that tubing that is conected into flow indicator cap does not turn at all to show if the chemical is sprying or not.i am looking mainly for tubing water/chemical diagram in order to verify the right connection.please help if you can bissell user. thanks


... Vacuums

Poor suction We bought a model home about 11 years ago and it had the Cental M&S Cyclonic Cleaning system. The suction has steadily been weakening. Now it is almost non-existant. I clean the filter bag in the main unit, but how clean does it need to be. Could there be a clog in the wall lines. If yes, how does one unclogg them. Thank you. I liked the system and would hate to just give up on it. Jean


This page has useful tips for unclogging a central vac. https://www.centralvacuumstores.com/cvs/trouble_help.php ... M&S Systems FX-3000 Bagged Central System Vacuum

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.


Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

How to clean rotating brushes or get into the suction tube to clean out


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Kenmore bagless 116.36932502 the interior filter port fills up very quickly-withih minutes of initial startup-- and has to be removed and cleaned constantly. Debris backs up into the interior of the main filter as well, the main canister never gets full. New problem with old machine!


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

U5468-900 handle on/off switch no longer works. Switch on main body works fine. Seems like handle assembly has worn out. Can I get a replacement?


... Hoover U5468-900 WindTunnel Bagged Upright Vacuum

My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.


... Euro-Pro Vacuums

The dirt is clogged inside the bissel little green 1400-7 hand held cleaning head. How can I unclog? Can the plastic piece be removed asw for the dirt is stuck on the sides of the cleaning handle?


... Bissell 1400 Little Green Pro Canister Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0460 seconds