Having problems with your Oreck XL2600 Vacuum ?

Need to remove base to replace belt. Is there a shortcut or must the Philips screws be removed?


Answers :

Repair Help & Product Troubleshooting for Oreck XL2600 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to remove base to replace belt. Is there a shortcut or must the Philips screws be removed?


... Oreck XL2600 Vacuum

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.


Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]


You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.


HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

How do you take of the base to change the belt? I removed the 4 screws but still cannot take the base off. I do not want to force (break) it... THANK YOU


If it's an Electrolux power head there will be a 5th screw same length in the base.2 at front corners, 1 front center, 2 mid way back all recessed. Good for asking , do not pry it should pull apart in you hands starting at the front corners ... Electrolux Vacuums

I got a Eureka 4471 at a garage sale and I need to replace the belt but I can't seem to find where any screws are to remove anything to access the belt! Help!


Below I have listed a link for your models manual which has instructions and a link for the belt you need. Hope it helps you!Owner's Manual ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need to open up this Hoover Uprite Runabout deluxe to replace the belt. I dont see any screws to remove to access. Model # U5064-940


You will find them on the bottom of the machine on the brush roll cover. This is the belt you need:Hoover Runabout Deluxe U5064-940 Belt ... Vacuums

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

How to remove bottom panel on eureka 4325 victory for belt replacement?I can not find screws.


... Vacuums

How do you replace a belt on the a Simplicity Synergy vaccuum? Removing the 2 screws on the bottom plate allows you to access the roller, but doesn't give you access to the drive motor. Any ideas?


... Simplicity 7850 Premier Bagged Canister Vacuum

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

How do I remove the bottom cover on powermate #26412690 to replace belt?


... Kenmore Vacuums

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

How do I replace the motor brushes in my DC11? I cannot dismantle beyond removing the pipe attachment. I've removed the 6 fixing screws that are visible, but the machine is still firmly "together" as if there are still screws that I've not located. Does it snap apart? Are there hidden screws? Paul


You can buy brushes but if the armature is overheating changing the brushes wont help ... Dyson Vacuums

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.


If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0808 seconds