Having problems with your Oreck XL2600 Vacuum ?

Cleaned tube but no suction

\015 The brush is turning fine and the tube is clear, but i am not getting any suction.\015\012Thanks!\015\012Chuck\015

Answers :

Then it is clogged in the inlet by the brush roll, or the fan has worn down too much.
Repair Help & Product Troubleshooting for Oreck XL2600 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to clean rotating brushes or get into the suction tube to clean out

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

SEBO vacuum cleaner makes a strange noise and shuts itself off after a few minutes. Suction not working when tube is attached, but works with hand-held portion only. Indicator light saying bag is full/clogged is on, but we've cleaned out the bag, cut away any fur/strings that were wrapped on the turning portion, and cleaned out the refuse valve. Not sure what else to do. Thanks!

... Sebo Vacuums

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?

... Bissell Vacuums

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?

Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.

You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have lost suction on my Bissell. It is also clogging in the Plastic tube that runs from the roller to the hose. What could have caused this? All filters have been cleaned, tube as well, but the problem still persists.

... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Cleaned tube but no suction

Then it is clogged in the inlet by the brush roll, or the fan has worn down too much. ... Oreck XL2600 Vacuum

Hello- My wand has lost a lot of it's suction. I am sure it's clogged somewhere. I cleaned everything after watching a video on U Tube, but it is still not sucking properly. My model is the Dyson DC28 Animal air muscle. I have only had it a few months. Also, I am not having any luck finding a local Dyson repair shop. I live in Pella, IA. Thank you, Kim

You do have a clog ... I feel certain. I have never worked on a Dyson. Please continue with your disassembly until you find that wad of chewing gum and cat hair and tell us how you did it.\015\012\015\012Im sure you will find a clog som ... Vacuums

Hi when i use tools to clean stairs etc loss of suction have checked tube seems ok.........

First of all, are you using a extended piece on the hose? if so then you should feel around where the hose and extended piece are see if air is leaking ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Dyson Dco7 animal not picking up from floor. Checked all connection valves and cleaned filter and brushes. Also check tube for cracks and nothing there. Wand suction is great just almost non on floor section. Please help!

I would check the "U" shape tube under wand that goes under body of machine. There is a button to release it. I would also check to make sure that your brushes are spinning properly. When you tip the vacuum back the brushes engage. Carefully place yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cleaning stairs no solution and no suction from tube

Clean your vacuum cleaner ... Hoover F5881-900 Vacuum

I have no suction through the tube so unable to clean with attachments. Why?

Its plugged up. Remove hose from appliance, and see if the cleaner sucks. If so, pull hose in a straight line and push a broom handle through the hose to clear debrie. Re attatch hose and this should clear the blockage ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have an old hoover turbopower approx 1986 i think its a U1102, the prob is it doesnt pick up anymore and i wondered if it had some sort of filter on it, ive cleaned all the tubes put new bag on but its still got weak suction, could you make any suggestions, thanks

Theres a tube that come up and emty's into the bag that tube is clogged.take the bag out and get a coat hanger and put a bend in it so the end is round then work it down the tube to push out the clog ... Vacuums

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho

Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene

... Vacuums

Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe

I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums

Poor suction We bought a model home about 11 years ago and it had the Cental M&S Cyclonic Cleaning system. The suction has steadily been weakening. Now it is almost non-existant. I clean the filter bag in the main unit, but how clean does it need to be. Could there be a clog in the wall lines. If yes, how does one unclogg them. Thank you. I liked the system and would hate to just give up on it. Jean

This page has useful tips for unclogging a central vac. https://www.centralvacuumstores.com/cvs/trouble_help.php ... M&S Systems FX-3000 Bagged Central System Vacuum

No suction my riccar 8850 has no suction. I cant find any clogs and there is some suction on the hose when using cleaning tools but when hooked up to the vaccum bag it wont clean

Replace your belt. Remove the baseplate, remove the brushroll, place a new belt around the motor pulley, then around the pulley on the brushroll, and pull the brushroll back into place in the nozzle. Spin it by hand to make sure it spins, (otherwise ... Riccar 8850 Vacuum

The suction for carpet cleaning is great but there is very little suction through the hose. I have cleaned out the hose but there is still very little suction. What else can I do?

Have you tried cleaning the hose from the vacuum end, the end that feeds the sweepings into the cannister/bag? Might be something close to that end of the hose.\015\012Also, one reason for a hose not to work is the possibility of a cut or broken hos ... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Dyson DC08 turbo brush won't turn but have suction in tube

Hi Cathy,I'm sorry to hear you're having difficulties with your DC08's turbo brush. As you've already checked the machine for blockages and washed the filter, I'd encourage you to get in touch with us directly so we can provide further assist ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.

Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.

... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3195 seconds