Having problems with your Oreck XL® Classic Bagged Upright Vacuum ?

The brushes are not spinning - Oreck XL® Classic Bagged Upright Vacuum


Answers :

It sounds to me that the drive belt to the brush is broken. To verify, or replace, you must take off the bottom cover.
Repair Help & Product Troubleshooting for Oreck XL® Classic Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes are not spinning - Oreck XL® Classic Bagged Upright Vacuum


It sounds to me that the drive belt to the brush is broken. To verify, or replace, you must take off the bottom cover. ... Oreck XL® Classic Bagged Upright Vacuum

Oreck upright brushes not spinning - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Brushs arc against spinning motor - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem


... Oreck XL2200 Bagged Upright Vacuum

Oreck xl gold roller brush not working - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Makes a clicking sound when vacuum spinning - Oreck XL® Platinum Pilot Bagged Upright Vacuum


... Oreck XL® Platinum Pilot Bagged Upright Vacuum

Installing roller brush for oreck XL 21 - Oreck XL Ultra Bagged Upright Vacuum


Uh, probably not sure what the issue is, but \015\0121. unplug unit.\015\0122. Remove the multiple screws from the bottom of the unit.\015\0123. remove the bottom baseplate (usually black)\015\0124. the brush roll is now visib ... Oreck XL Ultra Bagged Upright Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums


Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Brush is not spinning - Miele Powerhouse Plus Bagged Upright Vacuum


Usually, this is caused by the brush assembly end bearings becoming bound up with string, thread, and hair. Remove the brush and clean the bearings and end shafts. Oil them lightly with 3-1 oil or similar. Check the condition of the drive belt and re ... Miele Powerhouse Plus Bagged Upright Vacuum

Brush not moving - Sebo Felix Classic Bagged Upright Vacuum


May need new belt ... Sebo Felix Classic Bagged Upright Vacuum

U6485900 brush wont spin - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Check the belt av not broke this link is for the manualhttp://hoover.com/file/509/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dyson dc 33 brush bar not spinning - Dyson DC33 Bagged Upright Vacuum


... Dyson DC33 Bagged Upright Vacuum

Roller brush not rotating - Oreck XL Ultra Bagged Upright Vacuum


This may be the belt, and it may be the brush roller. \012\012I am leaning more towards the belt. The belt on any vac should be changed once a year, and for the pet lovers 2 times a year. \012\012Good luck. \012Mark ... Oreck XL Ultra Bagged Upright Vacuum

The brush stops spinning - Dirt Devil M086355 Bagged Upright Vacuum


... Dirt Devil M086355 Bagged Upright Vacuum

How to replace brush roller? - Oreck XL Ultra Bagged Upright Vacuum


Turn your vacuum over and there should be 5 or 6 Phillips screws that hold the base plate on. Take out those screws and that will give you access to where the brush roller is located. If you are replacing the roller it would be a good idea to repla ... Oreck XL Ultra Bagged Upright Vacuum

The brush does not spin when shapmooing - Kirby Ultimate G Bagged Upright Vacuum


Turn it upside down, see if you can the belt that driven up the motor gear, maybe it is mis allign or loosen. if it need a replacement then have it replace ... Kirby Ultimate G Bagged Upright Vacuum

Latch pin keeps spinning off belt door? - Oreck XL21 Bagged Upright Vacuum


The only correct solution is to replace the door. A small piece of tape works well too ... Oreck XL21 Bagged Upright Vacuum

Brush roller going backward - Oreck XL Ultra Bagged Upright Vacuum


Check that the wires are properly connected if the wires are crossed to the motor it will cause this effect ... Oreck XL Ultra Bagged Upright Vacuum

Brush doesn't rotate - Oreck XL Ultra Bagged Upright Vacuum


If the brush don't rotate.the first thing you need to do is check to make sure there is nothing jammed in the brush.Like a piece from a carpet,or hair.If it still don't work.then you need to change the belt inside the vacuum itself. ... Oreck XL Ultra Bagged Upright Vacuum

Brush heads won't spin - Bissell 3522 PowerForce Bagged Upright Vacuum


Your belt is stretched, worn or broken and therefore not turning the brush. Here is a link for the replacement belts you need and the manual which has instructions: ... Bissell 3522 PowerForce Bagged Upright Vacuum

My brush won't spin, and won't **** well - Kirby G6 Bagged Upright Vacuum


U need a new band inside they break and it stops the brushes spinning ... Kirby G6 Bagged Upright Vacuum

Brush roller stopped working - Oreck XL Ultra Bagged Upright Vacuum


The belt snapped. you will have to buy a new one at like walmart. and then take out all the screws on the bottom where the roller is. then you should see the broken belt. replace it by taking out the brushroll and slipping the new belt around the bru ... Oreck XL Ultra Bagged Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

Oreck xl 2100 vacuum belt keep on slipping - Oreck Xl 2100 Bagged Upright Vacuum


... Oreck Xl 2100 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1115 seconds