Having problems with your Oreck XL® Platinum Pilot Bagged Upright Vacuum ?

Makes a clicking sound when vacuum spinning - Oreck XL® Platinum Pilot Bagged Upright Vacuum


Answers :

Repair Help & Product Troubleshooting for Oreck XL® Platinum Pilot Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Makes a clicking sound when vacuum spinning - Oreck XL® Platinum Pilot Bagged Upright Vacuum


... Oreck XL® Platinum Pilot Bagged Upright Vacuum

Oreck upright brushes not spinning - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Brushs arc against spinning motor - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

Latch pin keeps spinning off belt door? - Oreck XL21 Bagged Upright Vacuum


The only correct solution is to replace the door. A small piece of tape works well too ... Oreck XL21 Bagged Upright Vacuum

The brushes are not spinning - Oreck XL® Classic Bagged Upright Vacuum


It sounds to me that the drive belt to the brush is broken. To verify, or replace, you must take off the bottom cover. ... Oreck XL® Classic Bagged Upright Vacuum

My plastic bag holder came off oreck xl - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck upright hard to push - Oreck XL2000 Bagged Upright Vacuum


If hard to push, only a few things to check:\015\012\015\012(1) Rear wheels will get hair or thread wrapped around axles, dust, etc. and be hard to turn. Make sure each wheel turns easily.\015\012\015\012(2) Small wheels on ne ... Oreck XL2000 Bagged Upright Vacuum

Is there a reset switch on the Oreck vacuum? - Oreck XL2200 Bagged Upright Vacuum


No.\015\012\015\012If the unit is not running at all, this is a 2 speed unit, right? I'd check for a failure of the diode that provides the 2 speed action.\015\012\015\012Next likely failure is a broken wire at motor. ... Oreck XL2200 Bagged Upright Vacuum

Oreck Inner Bag doesn't stay connected - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

How do you install oreck bag docking system - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

How to unclog the Oreck XL upright? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

How to disassemble oreck xl 21 vacuum - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck vacuum keeps turning off - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

Oreck xl 2100 vacuum belt keep on slipping - Oreck Xl 2100 Bagged Upright Vacuum


... Oreck Xl 2100 Bagged Upright Vacuum

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Need bags and can't find any to fit - Oreck XL Pro DS1700HY Bagged Upright Vacuum


That unit pictured is a rare bird I believe. Only source is likely an Oreck retail store or to call their 800-number an dorder from them. ... Oreck XL Pro DS1700HY Bagged Upright Vacuum

How do i stop dust coming out of vacuum - Oreck XL Ultra Bagged Upright Vacuum


Change the bag. ... Oreck XL Ultra Bagged Upright Vacuum

Position of o ring on oreck xl - Oreck XL Deluxe U3700 Bagged Upright Vacuum


... Oreck XL Deluxe U3700 Bagged Upright Vacuum

The bar on my oreck doesnt turn - Oreck XL Ultra Bagged Upright Vacuum


1) test the belt drive for worn or broken or crack2) bearing bar defective.LUBE 3) debris in the bar4) motor defective repairsee the diagrams. God bless you ... Oreck XL Ultra Bagged Upright Vacuum

How do I remove the bag - Oreck XL2200 Bagged Upright Vacuum


Unzip cloth bag look at paper bag it may have a spring loaded mech. holding it or it just snaps in place look at your replacement bag to see if its slotted it probably snaps into place watch how you remove the old bag and repeat the process ... Oreck XL2200 Bagged Upright Vacuum

Change belt on oreck xl intellashield - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Installing roller brush for oreck XL 21 - Oreck XL Ultra Bagged Upright Vacuum


Uh, probably not sure what the issue is, but \015\0121. unplug unit.\015\0122. Remove the multiple screws from the bottom of the unit.\015\0123. remove the bottom baseplate (usually black)\015\0124. the brush roll is now visib ... Oreck XL Ultra Bagged Upright Vacuum

Schematic for oreck xl 9100c - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

The vacuum drive makes a wining sound - Kirby G6 Bagged Upright Vacuum


Does It make the noise all the time or only when the machine is moving. If it does it only when you push the vacuum that noise is normal. The older Kirby transmissions make a whining noise when pushed. ... Kirby G6 Bagged Upright Vacuum

The inside bag is always coming off. - Oreck XL2200 Bagged Upright Vacuum


Assuming you are using the correct bags, a small bungee cord clipped on one side of the vac outlet passed under the lip of the bag opening and attached to the other side of the vac outlet, will do the trick. Good luck! ... Oreck XL2200 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1631 seconds