Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

Oreck xl 9100 how to replace the fan

\015 Does anyone know how to replace the fan,I have removed the nut but the fan wont come off ????????\015

Answers :

I just replaced the fan (plastic) on an XL9100. I assume you got the bottom plate off (5 screws).

Undo the single screw holding the suction housing in place.

Remove the two screws holding the motor in place and gently lift the assemble up, being careful not to stress the wires. The motor and fan assembly should now be exposed. If the nut holdling fan in place is removed, the whole fan should slide right off. If it does not, try a little WD-40 on the shaft and wiggle and move from side to side. (I slipped a small drill bit between the motor fan (motor cooling fan) to prevent the shaft from turning when you remove the nut.) Be sure you turn the nut counter-clockwise to remove it.

You should now have the fan off. Reverse the procedure to place the new fan - following the directions carefully as some assemblies need a washer and "feathered" washer on the top.

Assuming everything went well, it should work.

My 9100 sucked a magnetic bearing and trashed the metal fan to where suction was weak. The new fan works great.

Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oreck xl 9100 how to replace the fan

Hi,I just replaced the fan (plastic) on an XL9100. I assume you got the bottom plate off (5 screws).Undo the single screw holding the suction housing in place.Remove the two screws holding the motor in place and gently ... Oreck XL Ultra Bagged Upright Vacuum

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no

... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.

... Vacuums

Fan replacement I found the part to replace my broken fan. I've remove many screws, but I can't remove, what seems to be, the obvious plate to get to the broken fan.

Http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMP ... Kirby Ultimate G Bagged Upright Vacuum

Fan replacement I have to replace the fan on my g4 how do I get the old fan that is worn and broken off the shaft,,thanks for any help that you might be able to give

Detailed instructions on fan replacement HEREGoodLuck,Rocky:-) ... Kirby G4 Bagged Upright Vacuum

Oreck xl 9300 can not remove seal cup to change fan - appears glued?

You should be able to prise it of it will just be a push fit see link belowhttp://www.vacpartswarehouse.com/Oreck-XL9300-s/2925.htm ... Oreck Vacuums

Fan Replacement How do i get to the fan to replace it?

Remove the front piece and there about 4 screws u need to take out and remove that cover, the fan is right there, then u take out the screw that holds the fan blade or impeller as its called out, and put the new on, we just did it. if u have more qu ... Kirby G4 Bagged Upright Vacuum

My wall ceiling fan's control unit UC 9051T failed. Light switch button does not work. If I replace it with some generic universal unit, do I need to replace transducer located in the fan housing also, or all of them are compatible? Thanks in advance. M

First, you didn't say you checked that the bulb worked. Is that burned out?\015\012\015\012If bulb is ok, you will have to make sure the switch is matched with the fan (ususally a set of 4, 6 or 8 micro-switches have to be set the same i ... Vacuums

Fan and bearing replacement on a Kirby G6

If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

I bought a ceiling fan from lowe's, got it home got ceiling fan up in the bathroom, when we put in the light one of the halogen bulbs does not work , also two of the cobalt blue glass covers are cracked all the way through and one of the halogen light protectors also had a whole in the end of it. I called Lowe's they told me to contact you; day of purchase was 3/1/08 in Florence Al. store code # 04810-30108. Ceiling fan bar code 0 2403478512 2. 228365 52" Helix Chrome and Cobolt ceiling fa

If this is a new product and it is defective, take it back to Lowe's and insist on a replacement, talk to the manager if you have to. This site will only advise you on how to fix it. ... Vacuums

The fan on my Dirt Devil model 103 hand held vac cracked. I bought what was designated as the correct replacement fan but the hole in the center of the fan is a lot smaller than the shaft that it has

... Vacuums

I need diagram of replacing on/off switch for Oreck XL2600

Manual would not, they want you to pay a service tech.\015\012\015\012Believe this model has switch in grip, \015\0121. Unplug unit.\015\0122. remove screws from grip.\015\012separate the grip halves to access switch. ... Oreck XL2600 Vacuum

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft

... Vacuums

Oreck Orbiter Hi Could you e-mail me a wiring diagram for the Oreck Orbiter please? I need to replace the mains cable & the cable to the motor. Thank you, Helen Eccott.

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=618779&thid=681757\015\012Oreck Orbiter\015\012Posted by eccott on Jun 18, 2008\015\012Hi could you e-mail me a w ... Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum

My hoover 600 elite is really load. I took it all apart to find the motor fan is damaged with a broken off piece which must have been vacuumed up into the bag. If I replace it sith a new plastic fan will this quiet the vacuum? right now it is tremendously loud.

... Hoover Elite U5061-900 Bagged Upright Vacuum

Poor suction from the upright .I have replaced the hepa filter checked the fan belt and replaced the sponge filter.Thre does not appear to be any blockage. Any solution?

Check the hose for any tears. At the very top, directly under the handle, there is a metal tube inside of the hose. Pull the hose downwards, while holding onto the handle to stretch the hose as far as it will go. Check the very top of the hose for ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We need to replace the Fan Blades on our Phillips Fan as they heve got very fragile and they are breaking up!

Yes-- This is the big disadvantage of this type of Vacuum-- Stones and sand wear heavily on that impeller turning a very high rate of speed. This can be a tricky job----- depending on how long this fan has been on the motor sh ... Philips Vacuums

Kirby G3 made loud noise when running. Sprayed silicon in fan thinking it might be a bearing. Found a coin and nail in fan and removed. Tha vacuum would not turn on. Replaced switch and brushes. Still nothing. Did the silicon spray do something?

No - the silicon is an insulating material and would have no effect on the electrics of the vacuum. Most likely you have a bad connection - dismantle the vacuum again and check the wiring and the motor with an ohmmeter. Be very attentive with the bru ... Kirby Generation 3 Bagged Upright Vacuum

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

I have a Hampton Bay Midili fan which I just installed about a month ago and it was working fine. A few days ago when I flipped the switch on the light flickered on and off consistently until I turned the switch off. The remote also stopped working to control the fan and light. Since this model only can be controlled by the remote I am worried I will have to replace the remote already after only 1 month!

In many of these remote controlled lamps you cant use the new spiral light bulbs .. you can only use standard incandescent lights .. if thats not the trouble then you may indeed have a bad controller (in the fan) .. there is probably at least a 90 d ... Vacuums

I have a cooling fan on my wine cooler that burnt out, I need a replacement. I need a Heng Shan Fan model no# FS92252M 12v 0.2 amp

... Vacuums

Not sucking We have an Oreck XL and today it is blowing out dust instead of sucking it up. I just replaced the belt and about 6 months ago, we took it to our Oreck dealer and had it rehauled. I opened it up to check all and it all looked fine. Then I tuned on the machine while unzipped and noticed that the bad does not inflate as it used to. What can I do? Thanks, Connie [email protected]

You probable have a clog in the handle tube, or at the bottom, either by the brush or in the neck where the handle goes into. Unscrew that big black nut and pull the handle off of the bootom asm, then you can check it out and see where the clog is. ... Vacuums

Replacement parts where can i find replacement steam pocket towels online for the shark ultra steam blaster hard surface cleaner? I went online to www.sharkcompany.com & www.sharkvac.com and when I enter my model number S3325 search comes back with 0. Thanks

You can found them on amazon, take a look here: Amazon com Euro Pro S3325. I hope this was helpful. Cheers ... Euro-Pro S3325 Handheld Steam Vacuum

Broken fan need a repair man or service centre. If not a replacement fan for self repair. I live on the Gold Coast Ray is my name. Kirby Legend 1 model 2HE

Http://www.ultimatesanitarysupply.com/pdfs/VacuumMaintenance.pdf\015\012\015\012see the link ... Kirby Vacuums

Replacement belt Oreck UPR014T XL - Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum

Ok its sounds like you need a new brush roller and change your belt ... Oreck UPR014T XL Pro 14 Upright Vaccum Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0513 seconds