Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

How do I replace the brush roll on my oreck xl??

Answers :

Turn the vacume upside down. Remove the 5 screws on the bottom plate. 3 are near the brush roll, and 2 are near the back. Remove the bottom plate. take the belt off the motor end. pull up on both ends of the brush roll. Put new brush roll on making sure that you put both ends to the new position, not old. ( it is marked on one end, and there are marks on the side that goes up so the can match.)(If putting back the old brush roll you can switch to the old position. After a year or two you can switch the new brush roll to the old position.) Put the bels back on the motor shaft and then stretch and start the belt on the brush roll and rotate the brushroll by hand untill the belt is all the way on.
\015\012put the bottom plate back on and tighten the 5 bottom screws.
Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I replace the brush roll on my oreck xl??

Turn the vacume upside down. Remove the 5 screws on the bottom plate. 3 are near the brush roll, and 2 are near the back. Remove the bottom plate. take the belt off the motor end. pull up on both ends of the brush roll. Put new brush roll on making s ... Oreck XL Ultra Bagged Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

Agitator brush roll needs replacement

To change the beater bar you would need to open up from the bottom.To get the parts you would need to produce the model and serial numbers to your local hoover dealeror cheak on the internet for your closet dealer and order the part.There not to bad ... Hoover U8143-900 Upright Vacuum

How to replace Simplicity vac brush roll strips?

The caps will come out of the end of the metal roller. They can be difficult if it's been a long time as dirt and grime can build up. Try sticking a flat head screwdriver in and gently twisting to get the caps to slide out. ... Riccar Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Replace dyson 07 animal brush roll assembley

The end caps of the brush assembly which contain the bearings are only a push fit onto the spindle (quite tight). Remove these and the brush bar will pass through the drive belt loop. To achieve this the belt has to be stretched slightly so care has ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Replacement brush for Oreck ProPower Plus - Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright

... Oreck Pro Power Plus Upright Vacuum Refurbished Refurbished Pro Power Plus Upright

The roller on my Dyson DC24 quit rolling. I've taken out the brush, cleaned it, replaced it, locked it and push the reset button but it still isn't rolling. Help!!! I've only had this for about two months.

... Dyson Ball DC24 Bagless Upright Vacuum

Oreck xl doesn't pick up dirt but rather blows air out. Brush is clean but the belt and brush should be replaced however I am reluctant to put money toward vacuum if it's a broken machine. I think it's about 10 yrs old. I got it from a family member.

... Oreck XL Ultra Bagged Upright Vacuum

I have to replace the motor brushes in my Oreck XL model 2000RH. How do I remove the old brushes?

If it's an AC induction motor there are no brushes. ... Vacuums

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?

Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

Replacing the Brush Roll Control Knob

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacement belt for rolling brush attachment

... Vacuums

Oreck xl making whinning noise after replacing motor,belt and brush roller..

... Oreck XL Ultra Bagged Upright Vacuum

Replace belt nimble brush roll

... Electrolux Vacuums

No action Hi: My brush roll won't budge. After we cleaned out all the hoses and replaced a badly worn belt (burned?) when I turn it on the smell of burning rubber and smoke has continued. What hurts is that I don't think I've used the vacuum a total of 10 times ... and I had such high hopes. Ideas?

I had the same problem with the belt breaking and the roller not spinning. I read about giving the roller a couple of revolutions to seat the belt, so I put another new belt on. It still didn't spin. I realized it was the end cap that was not spinnin ... Eureka 2961AVZ Bagless Upright Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

Replace brush roll belt - Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

I have an oreck xl and the vaccum wont hardly push. Is it the belt? The brushes aren't turning when I lay it on it side. How do you replace the belt? If you can give detailed instructions I would so appreicate it . Thanks

On the side of the head you'll see a removable plate with one screw. Remove the screw and slide the plate towards the front until it's off. You'll see the belt. ... Oreck XL21 Bagged Upright Vacuum

Correct brush roll replacement part for a Beam #BM1383

... Beam Industries Vacuums

If the power brush does not roll, I presume it would be a belt. Where can I get a replacement for this model? Do you know of any diagram for the unit or how to remove the belt? Many thanks,

... Easy Flo SQ9020 Bagless Central System Cyclonic Vacuum

Need to replace red clips that hold rolling brush on 7901 Proheat

On the bottom of the machine, near the belt access area,\015\012is a red retainer plate that holds the black brush arm and\015\012brush in place. Using a Phillips head screwdriver remove the\015\012screw that holds the red retainer ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Brush roll won't turn before or after belt replacement.

Did you check the brush roll, the ends should turn freely, if not then replace the brush roll. ... Hoover Vacuums

How to replace brush roller? - Oreck XL Ultra Bagged Upright Vacuum

Turn your vacuum over and there should be 5 or 6 Phillips screws that hold the base plate on. Take out those screws and that will give you access to where the brush roller is located. If you are replacing the roller it would be a good idea to repla ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0600 seconds