Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

How do you change the belt? - Oreck XL Ultra Bagged Upright Vacuum


Answers :

Two methods:
\015\012
\015\0121) If your vacuum has the small side door on the cover of the lower unit, can remove the screw, it will allow you to access the belt. I assume old belt is broken, so what you see will be the end of the motor shaft ( a small, round shaft about 1/4" in diameter) and the end of the brush roll, (about a 3/4" to 1" round plastic knob attached to the end of the brush roll.) Make sure each of these turns freely, otherwise you are going to burn up another belt. Slide belt over these two points, replace the access cover, and turn on.
\015\012
\015\0122) If you have an older unit or maybe the commercial unit, you will need to remove the bottom cover. A bunch of screws, don't remember how many at this time. After you remove the cover, you will see the two points I described above. Replace belt then replace the bottom cover (called a baseplate on a parts diagram probably). Make sure the rubber bumper is properly seated, it can be a pain sometimes.
\015\012
\015\012While inside the unit under either scenario, I always would try to clean out any excess dirt, dust, etc.
\015\012
\015\012
Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Change belt on oreck xl intellashield - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

How do you change the belt? - Oreck XL Ultra Bagged Upright Vacuum


Two methods:\015\012\015\0121) If your vacuum has the small side door on the cover of the lower unit, can remove the screw, it will allow you to access the belt. I assume old belt is broken, so what you see will be the end of the motor sh ... Oreck XL Ultra Bagged Upright Vacuum

No manual, how do you change the belt? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

How do you install oreck bag docking system - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck xl 2100 vacuum belt keep on slipping - Oreck Xl 2100 Bagged Upright Vacuum


... Oreck Xl 2100 Bagged Upright Vacuum

How to disassemble oreck xl 21 vacuum - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

My plastic bag holder came off oreck xl - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Installing roller brush for oreck XL 21 - Oreck XL Ultra Bagged Upright Vacuum


Uh, probably not sure what the issue is, but \015\0121. unplug unit.\015\0122. Remove the multiple screws from the bottom of the unit.\015\0123. remove the bottom baseplate (usually black)\015\0124. the brush roll is now visib ... Oreck XL Ultra Bagged Upright Vacuum

MANUAL ORECK XL21 - Oreck XL Ultra Bagged Upright Vacuum


The Oreck XL21 is a refurbished XL vacuum. All Oreck manuals are available here: http://www.oreck.com/Product-User-Guides/global-user ... Oreck XL Ultra Bagged Upright Vacuum

Oreck xl U3620HH4 White Smoke - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Vacuum is not turning on - Oreck XL Ultra Bagged Upright Vacuum


Try a ruling out a couple of things first before opening up the handle:\015\012\015\0121) First lets make sure your outlet has power\015\012 a) can you plug anything else in and have it work?\015\012 b) is the vacuum plugged ... Oreck XL Ultra Bagged Upright Vacuum

Oreck xl not sucking - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL suddenly lost power - Oreck XL Ultra Bagged Upright Vacuum


Wiring in handle has loose connection or the brushes in the motor needs replacing. cost $18 for new ones. ... Oreck XL Ultra Bagged Upright Vacuum

Diagram for motor wiring oreck - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck xl gold roller brush not working - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

How to remove oreck 2605 hh motor - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

The bar on my oreck doesnt turn - Oreck XL Ultra Bagged Upright Vacuum


1) test the belt drive for worn or broken or crack2) bearing bar defective.LUBE 3) debris in the bar4) motor defective repairsee the diagrams. God bless you ... Oreck XL Ultra Bagged Upright Vacuum

How do i stop dust coming out of vacuum - Oreck XL Ultra Bagged Upright Vacuum


Change the bag. ... Oreck XL Ultra Bagged Upright Vacuum

Schematic for oreck xl 9100c - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

How do I take oreck apart? - Oreck XL Ultra Bagged Upright Vacuum


5 screws on bottom plate. Then couple to hold fan housing and motor. Not a bad job just takes a little juggling finesse. ... Oreck XL Ultra Bagged Upright Vacuum

Replacing belts on U3109 hoover vacuum - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

How do you change the belt on an oreck upright xl ultra


... Oreck XL2200 Bagged Upright Vacuum

Change belt on hoover savvy bag and bagless upright vacuum


... Hoover U8155-900 Savvy Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1173 seconds